Skip to lesson content

Lesson 4 of 13

Ray Optics and Optical Instruments · Lesson 4 of 13

Total Internal Reflection and Optical Fibres

“Explain the critical-angle threshold and apply it to prisms, escape cones and guided light.”

Learning Objectives

• Derive the critical angle from Snell’s law. • Check both conditions for total internal reflection. • Calculate an escape cone and a fibre acceptance angle. • Explain prism reflection, fibre guiding and real transmission losses.

When an outgoing refracted ray becomes impossible

Look upward from beneath water. Rays striking the surface near the normal can escape into air, while sufficiently oblique rays reflect back. At a boundary from index n₁ to smaller index n₂, Snell’s law gives sin r = (n₁/n₂) sin i. Increasing incidence i increases r faster. At the critical angle i_c the transmitted ray grazes the surface, so r = 90°. Beyond this threshold Snell’s law would require sin r > 1, and no propagating refracted ray exists in the second medium.

Critical angle and total-reflection conditionsLaTeX
Angles are measured from the normal in the higher-index incident medium. At i = i_c the refracted ray is grazing; use a strict inequality for total internal reflection.

Total internal reflection is a special case of internal reflection, not every reflection inside glass. Below the critical angle, light is partly transmitted and partly reflected. At an ideal transparent lossless interface above the critical angle, the reflected power equals incident power. Wave theory also predicts a field extending a short distance into the second medium, called an evanescent field; saying “no transmission” here means no ordinary transmitted ray carrying energy away into a semi-infinite lossless second medium. Absorption, nearby material and surface imperfections can change the ideal result.

From n = 1.50 below to air abovebelow criticali = 30.0°at criticali = 41.8°above criticali = 55.0°Blue: incident/transmitted rays. Red: internal reflection. Critical angle = 41.81°.
The critical-angle threshold— A water-like higher-index region lies below the boundary. The three ray paths use Snell’s law.
Higher-index medium to airIndexCritical angle
Water1.3348.75°
Crown glass1.5241.14°
Dense flint glass1.6238.12°
Diamond2.4224.41°

A small critical angle means a narrow cone of internal directions can escape at a single smooth face. It helps explain why appropriately cut diamond facets can retain light through several internal reflections before it emerges. Reflection alone does not create extra energy or brightness; cut, illumination and dispersion affect what the observer sees. Over a hot road, changing air temperature produces a gradual refractive-index gradient. Curved light paths can make sky light appear below, as if reflected from water. This mirage should not be pictured as reflection from a literal puddle or necessarily a sharp boundary.

Prisms as reflectors

A right-angle prism can turn light by 90° when a ray enters one short face normally, reaches the hypotenuse at 45°, reflects, and leaves the other face normally. For this to be total internal reflection into air, i_c < 45°, or n > √2. Orienting a ray normally to the hypotenuse can make it reflect twice from the other faces and return with a 180° direction change. Suitable prism arrangements can also invert an image while retaining its size. Putting the prism in a higher-index surrounding liquid can destroy total reflection because it increases the critical angle.

The escape circle above an underwater lamp

A light cone meets a surface

Problem
A point lamp is 80 cm below water of n = 1.33. Find the radius and area of the surface region through which its direct rays can emerge into air.

  1. 1.The largest escaping incidence is i_c = arcsin(1/1.33) = 48.75°. The limiting radius is a = h tan i_c.
  2. 2.tan i_c = 1/√(n² − 1), so a = 0.80/√(1.33² − 1) = 0.912 m.
  3. 3.Area = πa² = 2.615 m². Rays reaching points outside this circle have incidence above the threshold. The edge is the limiting grazing direction, not a finite upward beam.

Core, cladding and acceptance

An optical fibre has a higher-index core and a lower-index cladding. Light launched within a suitable cone can reflect repeatedly at the core–cladding boundary. The entrance angle to the axis is not the angle used in the critical-angle test: for a straight fibre and a meridional ray inside the core at axial angle θ, the sidewall incidence is 90° − θ. Total reflection requires sin(90° − θ) > n_clad/n_core. Thus cos θ > n_clad/n_core. Combine this with refraction at the plane entrance, n_out sin θ_in = n_core sin θ, to obtain the limiting acceptance below.

Acceptance cone of a straight step-index fibreLaTeX
Meridional-ray model, plane entrance normal to the axis. If the right side exceeds n_out, all physically entering angles up to grazing satisfy the limiting condition; do not take arcsin of a number greater than one.
A guided meridional ray in a straight fibrelower-index claddinghigher-index coreiθwall incidence i = 90° − axial angle θSchematic step-index model; actual bending and losses require further checks.
Guiding by repeated internal reflection— Core index exceeds cladding index. The internal axial angle and wall-normal incidence are complementary.
A clad and an unclad light pipe

Problem
A core has n = 1.68 and cladding n = 1.44; light enters from air. Find the limiting entrance half-angle. What if the cladding is removed and air surrounds the core?

  1. 1.The numerical aperture is √(1.68² − 1.44²) = 0.8653, so θ_max = 59.92°. Actual total-reflection rays lie inside the limiting cone.
  2. 2.Without cladding the square root becomes √(1.68² − 1) = 1.3500 > 1. Every entrance angle below 90° in air is within the ideal meridional acceptance range.
  3. 3.This does not mean that all injected power is usefully guided in a real fibre. Bends, absorption, scattering and coupling losses remain.

Fibres carry modulated light for communication and can deliver illumination or images in medical instruments. A coherent imaging bundle must preserve the relative arrangement of fibres to transmit an image. Good transparency is essential: total reflection at a wall does not prevent absorption along the material. Strong bending can reduce a wall-incidence angle below its critical value and cause leakage. To demonstrate the threshold, use a ray box and a transparent block or supervised low-power beam in slightly scattering water, varying internal incidence while keeping the boundary fixed; never direct a beam toward eyes.

Quick Quiz

Quiz

Quick check

Total internal reflection requires light to travel

Explanation: Both index ordering and angle threshold are necessary.

Quick check

At the critical angle, the refraction angle is

Explanation: The refracted ray grazes the interface.

Quick check

For glass n = 1.50 surrounded by air, i_c is about

Explanation: arcsin(1/1.50) = 41.81°.

Quick check

To guide by total reflection, a step-index fibre normally has

Explanation: A lower-index cladding permits internal critical-angle reflection.

Quick check

A fibre can lose guided light when sharply bent because

Explanation: The local geometry changes the incidence condition.

Practice Problems

Practice Problems
  1. Find the critical angle from n = 1.62 glass to air and assess a 40° incident ray.
  2. A 45° reflecting prism has n = 1.50. Will it work by total reflection in air and in water of n = 1.33?
  3. Derive the escape-circle radius for a lamp at depth h in a liquid of index n viewed across a flat surface into air.
  4. A fibre has core index 1.50 and cladding index 1.48. Find its limiting air entrance half-angle.
  5. Explain why ideal total reflection does not imply zero attenuation along kilometres of real fibre.

i_c = arcsin(1/1.62) = 38.12°. Since 40° > i_c and propagation is from higher to lower index, the ray is totally internally reflected in the ideal lossless model.

Key Takeaways

Key Takeaways

• Total internal reflection needs higher-to-lower index propagation and i > i_c. • At critical incidence the transmitted ray is grazing. • sin i_c equals the lower index divided by the higher index. • Prisms can turn light without a reflective coating when the threshold is satisfied. • Core and cladding indices set a fibre’s entrance acceptance cone. • Fibre axial angles differ from wall-normal incidence angles. • Real fibres have absorption, scattering, coupling and bending losses.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…