Skip to lesson content

Lesson 8 of 13

Ray Optics and Optical Instruments · Lesson 8 of 13

Combining Lenses and Returning Light Paths

“Apply sequential imaging to contact and separated lenses, then explain a lens–liquid–mirror measurement.”

Learning Objectives

• Derive power addition for lenses in contact. • Translate coordinates correctly between separated lenses. • Distinguish effective focal length from back focal distance. • Explain autocollimation and determine a liquid index.

A first image becomes the next object

A camera or microscope contains several refracting components. To trace them, calculate the image the first component would form, then use that point as the object for the next component. If rays meet it before the next lens, they arrive there diverging from a real object. If they encounter the next lens while still converging toward it, it is a virtual object. The intermediate image need not physically form before the next optical action. For a sequence of thin lenses, total transverse magnification is the product of the individual signed magnifications because each image height becomes the next object height.

Contact lenses: why powers add

For two thin lenses with coincident centres in the same outside medium, write 1/v₁ − 1/u = 1/f₁ for the first. For the second, its object coordinate is u₂ = v₁, so 1/v − 1/v₁ = 1/f₂. Add them to cancel the intermediate reciprocal distance. The result is 1/v − 1/u = 1/f₁ + 1/f₂. Comparing with an equivalent thin lens gives reciprocal-focal-length addition. Convert every focal length to metres before adding powers in dioptres.

Contact-lens combinationLaTeX
The first two relations require thin lenses in contact in a common medium. Magnification multiplication also applies to separated sequential stages.
A converging lens and a stronger diverging lens

Problem
Combine f₁ = +30 cm and f₂ = −20 cm in contact.

  1. 1.1/F = 1/30 − 1/20 = −1/60 cm⁻¹, so F = −60 cm.
  2. 2.P₁ = +3.333 D, P₂ = −5.000 D and total P = −1.667 D.
  3. 3.The negative net power means a parallel beam diverges; a positive component does not guarantee a positive combination.

Separated lenses require a coordinate shift

Put lens 1 at x = 0 and lens 2 at x = d, with light still travelling right. If the first calculated image is at x = v₁, its object coordinate from lens 2 is u₂ = v₁ − d. Do not insert v₁ directly when d is nonzero. Then calculate v₂ from 1/v₂ − 1/u₂ = 1/f₂. The final global coordinate is d + v₂, not merely v₂.

Translate the object coordinate at the next lensprincipal axislens 1: +180lens 2: −260P: would-be first imageLengths are schematic. Dashed segments show the path without lens 2.
Two separated lenses in a converging bundle— The first image point lies beyond lens 2, making it a virtual object for that lens.
The coordinate shift changes the result

Problem
Use f₁ = +30 cm and f₂ = −20 cm separated by 8 cm. A 1.5 cm object is 40 cm before lens 1. Find the final image and height.

  1. 1.For lens 1, 1/v₁ = 1/30 − 1/40 = 1/120, so v₁ = +120 cm and m₁ = −3.
  2. 2.Lens 2 receives a converging bundle with u₂ = 120 − 8 = +112 cm. 1/v₂ = −1/20 + 1/112 = −23/560, so v₂ = −24.35 cm.
  3. 3.m₂ = v₂/u₂ = −5/23. Therefore m = 15/23 = +0.6522 and final height is +0.9783 cm. The final image lies 24.35 cm left of lens 2, or x = −16.35 cm from lens 1, and is virtual for the outgoing bundle.

Two meanings of focal distance

For an incoming parallel ray at height y, the first lens changes its small slope from zero to −y/f₁. After travelling d its height at lens 2 is y₂ = y(1 − d/f₁). Lens 2 adds slope −y₂/f₂. The total outgoing slope is therefore −y[1/f₁ + 1/f₂ − d/(f₁f₂)]. Define the bracket as 1/F: this is the system’s effective focal length in a common surrounding medium. The axial distance from lens 2 to where this ray crosses the axis is b = −y₂/slope, giving b = F(1 − d/f₁). This back focal distance is measured from the last physical lens, whereas F is measured from a principal plane of the equivalent system.

Separated thin lenses in one mediumLaTeX
Paraxial slope derivation; d and focal lengths use the same unit. b is the signed back focal distance from lens 2 for incidence through lens 1.

For +30 cm and −20 cm lenses separated by 8 cm, 1/F = −1/300 cm⁻¹, so F = −300 cm. In that order b = −220 cm. Reverse the pair and b = −420 cm, although F remains −300 cm. Thus the effective focal length is useful and order-independent for this reversed pair in the same medium, while a focus distance measured from the final lens is order-dependent. A question using “effective focal length” without specifying its reference plane can confuse these quantities. If total power is zero, the system can be afocal; a finite back focal distance is then absent.

Autocollimation: a needle meets its returned image

Place a convex lens above a horizontal plane mirror, with an axial needle above the lens. When the needle is at the front focal plane of the combined refracting system, outgoing rays below it are parallel. The plane mirror reverses them and the refracting system focuses them back at the same needle plane. This is autocollimation. Coincidence alone should be checked by eliminating parallax between needle and image while moving the viewing eye sideways. After reflection, propagation reverses; reset the local positive axis if calculating the return path separately.

Finding a liquid index

Problem
A glass equiconvex lens of n_g = 1.50 gives coincidence at needle distance 30 cm over a plane mirror. A thin liquid layer below it changes coincidence distance to 45 cm. Determine n_liquid.

  1. 1.In air, 1/f_g = (n_g − 1)(2/R), so with n_g = 1.50 the radius magnitude is R = f_g = 30 cm.
  2. 2.The thin layer forms a plano-concave liquid lens between the lower curved glass face and plane mirror. Its power in the equivalent thin contact model is P_liquid = −(n_liquid − 1)/R.
  3. 3.The combined power is 1/45 = 1/30 − (n_liquid − 1)/30 in cm⁻¹. Multiplying by 30 gives 2/3 = 1 − (n_liquid − 1), hence n_liquid = 4/3.
  4. 4.The result assumes negligible layer/lens separation, paraxial rays and the intended liquid geometry. Do not double the inferred one-way focal power just because the light returns.

Quick Quiz

Quiz

Quick check

For thin lenses in contact, add their

Explanation: Their reciprocal-distance equations cancel the intermediate image term.

Quick check

For lens 2 at x = d and first image x = v₁, its object distance is

Explanation: Coordinates must be translated to the second centre.

Quick check

A first image lies beyond lens 2 before rays reach it. For lens 2 it is

Explanation: Incoming rays are still converging toward that point.

Quick check

The back focal distance of separated lenses is

Explanation: Effective focal length instead uses an equivalent principal plane.

Quick check

In autocollimation, the needle is at the effective front focal plane when

Explanation: The plane mirror reverses a collimated bundle which is refocused on return.

Practice Problems

Practice Problems
  1. Combine +5 D and −2 D thin lenses in contact. Find the equivalent focal length.
  2. A +10 cm lens has a real object 30 cm before it. A −10 cm lens sits 5 cm later. Find the output.
  3. Show why contact power addition fails for +30 cm and −20 cm lenses separated by 8 cm.
  4. Find the back focal distances of that separated pair in the two orders.
  5. In a needle–lens–plane-mirror experiment, coincidence occurs at 30 cm dry and 45 cm with liquid. Explain the index calculation for equiconvex n_g = 1.50 glass.

P = 5 − 2 = +3 D. F = 1/3 m = +33.3 cm, so the system is converging. Adding focal lengths would not represent the combined slope changes.

Key Takeaways

Key Takeaways

• Contact powers add algebraically. • Intermediate images can be real images for one stage and virtual objects for another. • Separated components require u₂ = v₁ − d. • Total transverse magnification is the product of signed stage magnifications. • Separated-lens effective power includes a distance term. • Effective focal length and back focal distance use different reference planes. • Autocollimation locates the front focal plane through a returned image.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…