Electrostatic Potential and Capacitance · Lesson 10 of 11
Stored Energy, Field Energy and Charge Sharing
“Explain capacitor energy, distinguish source work from field energy and account for energy during redistribution.”
• Use all three equivalent capacitor-energy expressions. • Explain the charging-work origin of the factor one-half. • Compare dielectric insertion energy under fixed Q and fixed V. • Calculate charge-sharing voltage and account for reduced stored energy.
Why the final voltage is not the voltage throughout charging
An initially uncharged capacitor offers very little electrical opposition to separating the first small amount of charge. As charging proceeds, its voltage rises and each further coulomb requires more work. Multiplying the final voltage by the full final charge therefore overestimates the energy stored. For a fixed linear capacitance the voltage rises linearly with transferred charge, so its average during quasistatic charging from zero is half the final value.
A charging-work explanation
For an intermediate plate charge q, the voltage is q/C. Transferring a further dq against that voltage requires dW = (q/C)dq. Sum these small increments from zero to Q. This argument explains the energy relation, rather than asking you to memorise a factor one-half. The source’s more detailed derivation is included here as explanatory enrichment; the basic application requires the resulting energy formulas.
If an ideal fixed-voltage battery charges an initially empty capacitor through a resistive path, its work is Wbattery = VQ = CV². Only ½CV² remains electrostatically stored; the other half is dissipated in the transient circuit under the usual resistive charging model. Conservation of energy still holds. A reversible source whose voltage tracks the capacitor can transfer charge with much less dissipation. Do not confuse the energy of the final state with the energy cost of every possible charging procedure.
Energy belongs to the field configuration
For a vacuum parallel-plate capacitor, substitute C = ε₀A/d and V = Ed into U = ½CV². This gives U = ½ε₀E²Ad. The factor Ad is the field-filled volume in the ideal central-gap model; dividing by it gives energy per volume. Although this derivation uses parallel plates, the vacuum electric energy-density expression is general for an electrostatic field.
Problem
A 12 pF capacitor is at 50 V. Find Q and U.
- 1.Q = CV = (12 × 10⁻¹²)(50) = 6.0 × 10⁻¹⁰ C.
- 2.U = ½CV² = ½(12 × 10⁻¹²)(2500) = 1.5 × 10⁻⁸ J = 15 nJ.
- 3.The check ½QV = ½(6.0 × 10⁻¹⁰)(50) gives the same value. Using QV alone would double the stored energy.
Dielectric insertion: account for the source
Insert a K dielectric slowly into an isolated charged capacitor at fixed geometry, with negligible loss. Q stays fixed and C grows by K, so U = Q²/(2C) falls to U₀/K. The energy decrease can appear as mechanical work: the field pulls the dielectric in, and a restraining external agent can extract work. If the dielectric accelerates or dissipates energy, those channels must also be counted.
With an ideal battery connected, V stays fixed, so U = ½CV² rises to KU₀. The battery supplies ΔQ = (K − 1)C₀V and does work VΔQ = 2(K − 1)U₀. Half that additional work increases stored energy; for slow lossless insertion the rest is available as mechanical work. Both constraints can therefore produce attraction into the gap even though stored field-plus-material energy changes in opposite directions.
| Full filling; unchanged gap | Q fixed | V fixed |
|---|---|---|
| Final stored energy | U₀/K | KU₀ |
| Battery work during insertion | 0 | 2(K − 1)U₀ |
| Mechanical work available in slow lossless insertion | U₀(1 − 1/K) | (K − 1)U₀ |
Charge sharing: conserve the right quantity
Disconnect a capacitor C₁ initially at V₀ from its source, then connect its positive plate to the corresponding plate of an initially uncharged C₂ and likewise connect the other plates. Charge redistributes until the parallel voltages agree. The combined positive-node charge is conserved, so C₁V₀ = (C₁ + C₂)Vf. Electrostatic stored energy generally decreases during the transient even though charge is conserved.
Problem
A 600 pF capacitor at 200 V is disconnected and joined to an uncharged 600 pF capacitor. Find final voltage and stored-energy decrease.
- 1.Initial positive-node charge is CV₀ = 120 nC. The final total capacitance is 1200 pF, so Vf = 100 V. Each capacitor then carries 60 nC in magnitude.
- 2.Ui = ½(600 × 10⁻¹²)(200)² = 12 μJ. Uf = ½(1200 × 10⁻¹²)(100)² = 6 μJ. The decrease is 6 μJ.
- 3.The decrease is transferred to heat and possibly radiation during redistribution; charge conservation does not require conservation of electrostatic energy alone.
Quick Quiz
Quiz
Stored energy in a linear capacitor is
Integrating the increasing charging voltage gives half the final charge times final voltage.
At fixed Q, doubling capacitance makes U
U = Q²/(2C) is inversely proportional to C for fixed Q.
At fixed V, doubling capacitance makes U
U = ½CV² is proportional to C for fixed V; a source exchanges charge.
Two equal capacitors share charge, one initially at V₀ and the other empty. Final voltage is
Conserved terminal charge CV₀ is distributed over capacitance 2C.
After charge sharing, reduced electrostatic stored energy
Energy transfers to other channels during the transient; only electrostatic storage energy decreased.
Practice Problems
- A 4 μF capacitor stores 2 mJ. Find its voltage and charge magnitude.
- A vacuum field has magnitude 1000 V m⁻¹ in volume 2 × 10⁻⁶ m³. Estimate its energy.
- An isolated capacitor initially stores 90 μJ. Insert a K = 3 dielectric fully and slowly. Find final stored energy and ideal available mechanical work.
- Repeat the previous energy scenario with an ideal fixed-voltage source connected.
- A 2 μF capacitor at 90 V shares charge with an initially empty 4 μF capacitor. Find final voltage, each charge and energy decrease.
From U = ½CV², V = √(2U/C) = √[(4 × 10⁻³)/(4 × 10⁻⁶)] = √1000 ≈ 31.6 V. Q = CV ≈ (4 × 10⁻⁶)(31.6) = 126 μC. Check that ½QV = 2 mJ.
Key Takeaways
• Stored energy is Q²/(2C) = ½CV² = ½QV. • The factor one-half comes from voltage increasing during charging. • Battery work can exceed the final stored energy. • Vacuum electric energy density is ½ε₀E². • Dielectric insertion lowers energy at fixed Q but raises it at fixed V. • Include source work when voltage is maintained. • Charge sharing conserves node charge while stored energy can become heat and radiation.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…