Skip to lesson content

Lesson 9 of 11

Electrostatic Potential and Capacitance · Lesson 9 of 11

Capacitors in Series, Parallel and Mixed Networks

“Use node connections and charge conservation to derive equivalent capacitance and recover individual voltages.”

Learning Objectives

• Identify series and parallel connections from electrical nodes. • Derive equivalent capacitance for both basic combinations. • Calculate individual charges and potential differences. • Check mixed-network results against conservation and size bounds.

Connections matter more than drawing position

Two points joined by ideal wire are one electrical node at equilibrium, even when drawn far apart. Capacitors are parallel when their terminals connect to the same two nodes; they then have the same potential difference. Capacitors form a simple series chain when the intermediate nodes connect only successive capacitors, with no branching. Redraw tangled wires into labelled nodes before choosing a formula.

Parallel: shared voltage, additive terminal charge

Connect C₁ and C₂ between nodes A and B with voltage V. The positive-node plate charges are Q₁ = C₁V and Q₂ = C₂V. The charge drawn from that source terminal is their sum. Replacing both with a single equivalent capacitor means preserving terminal charge for a given terminal voltage, so CeqV = (C₁ + C₂)V.

Parallel combinationLaTeX
Parallel capacitors share voltage, not generally charge. The equivalent capacitance is larger than any individual positive capacitance. Physically the connection resembles increasing effective plate area.

Series: start with an isolated intermediate node

Consider two initially uncharged capacitors in series with an isolated intermediate wire and its attached plates. That middle conductor has initial net charge zero and cannot exchange net charge with the outside. If one of its plates acquires −Q, the other must acquire +Q. The charge magnitudes on successive capacitors are therefore equal in the usual initially uncharged series chain. This conclusion follows from conservation of middle-node charge, not from an assertion that every capacitor always has the same charge.

The total terminal voltage equals the sum of successive voltage drops, V = V₁ + V₂. Because each has charge magnitude Q, V = Q/C₁ + Q/C₂. Divide by Q and compare with V = Q/Ceq to obtain the reciprocal sum. Initially charged internal nodes can require a more general node-charge calculation; the simple equal-Q statement must not be applied without its assumption.

Initially uncharged series chainLaTeX
For two capacitors, Ceq = C₁C₂/(C₁ + C₂). The equivalent capacitance is smaller than the smallest component. Smaller capacitance takes a larger share of the series voltage.
Capacitor topologyCapacitor topologySeriesParallelABC₁C₂Floating nodeC₁C₂ABIdeal wires define nodes; series chain initially uncharged.
The same two capacitors connected in series and in parallel— Labels A and B identify external nodes. A floating initially neutral middle node enforces equal charge magnitudes in the series pair; parallel branches share both endpoints.
Unequal components in series

Problem
Connect 3 μF and 6 μF in series across 12 V, initially uncharged. Find equivalent capacitance, charge and individual voltages.

  1. 1.1/Ceq = 1/3 + 1/6 = 1/2 in μF⁻¹, so Ceq = 2 μF. The shared charge magnitude is Q = (2 μF)(12 V) = 24 μC.
  2. 2.V₁ = 24/3 = 8 V and V₂ = 24/6 = 4 V. Their sum is 12 V. The smaller capacitor has the larger voltage.
  3. 3.Each capacitor has opposite charges on its two plates. “Equal series charge” means equal magnitudes, not that every plate has the same sign.
The same components in parallel

Problem
Connect the same 3 μF and 6 μF capacitors directly in parallel across 12 V.

  1. 1.Ceq = 3 + 6 = 9 μF. Both voltage differences are 12 V.
  2. 2.Charges are Q₁ = (3 μF)(12 V) = 36 μC and Q₂ = (6 μF)(12 V) = 72 μC. Terminal charge is 108 μC.
  3. 3.Changing topology has changed the equivalent capacitance from 2 μF to 9 μF, even though the component values are unchanged.

Reduce a mixed network and then expand it

Find a genuine series or parallel subgroup, replace it by its equivalent, and repeat until one capacitance remains. Then work backwards. A subgroup in series receives the series charge; a subgroup in parallel receives the common voltage. Use those values to recover the original component charges and voltages. Never stop with Ceq when the question asks for individual capacitor states.

Mixed network with a parallel branch

Problem
Three 10 μF capacitors form a series branch across 500 V. A fourth 10 μF capacitor is directly across the same source. Find Ceq and all capacitor charges.

  1. 1.The three-capacitor branch has Cs = 10/3 μF. It is parallel to the fourth capacitor, so Ceq = 10/3 + 10 = 40/3 μF ≈ 13.3 μF.
  2. 2.Each series capacitor has charge Qs = (10/3 μF)(500 V) = 1667 μC ≈ 1.67 mC. Each takes 500/3 V ≈ 167 V.
  3. 3.The directly connected capacitor has charge (10 μF)(500 V) = 5000 μC = 5.00 mC and voltage 500 V. Total source-terminal charge is 6.67 mC. The sum of all four positive capacitor charge magnitudes is not the terminal charge, because internal series nodes store induced opposite charges.

Sanity checks before accepting an answer

A series equivalent must be below the smallest capacitance; a parallel equivalent must exceed the largest. Series voltages must sum to the terminal voltage, and parallel voltage differences must match. At an isolated intermediate node check signed net charge, rather than adding absolute charge magnitudes. A real series capacitor can exceed its voltage rating even when the total applied voltage looks acceptable, because unequal capacitances divide voltage unequally. Ideal calculations omit leakage and manufacturing tolerances.

Quick Quiz

Quiz

Quick check

Two capacitors are parallel when

Explanation

Parallel is a connection property defined by shared endpoints.

Quick check

For 2 μF and 3 μF in series, Ceq is

Explanation

Ceq = (2 × 3)/(2 + 3) = 1.2 μF.

Quick check

In a usual initially uncharged series pair, the smaller capacitor has

Explanation

The shared Q gives Vi = Q/Ci, so smaller Ci means larger Vi.

Quick check

Capacitors 2 pF, 3 pF and 4 pF in parallel have Ceq

Explanation

Capacitances add in parallel: 2 + 3 + 4 = 9.

Quick check

What enforces equal charge magnitudes in a simple initially uncharged series chain?

Explanation

An isolated initially neutral middle conductor keeps zero net charge, giving equal-and-opposite charges on its attached plates.

Practice Problems

Practice Problems
  1. Three 9 pF capacitors are connected in series across 120 V. Find Ceq and each voltage.
  2. Capacitors 2 pF, 3 pF and 4 pF are in parallel across 100 V. Find all charges.
  3. A parallel pair 2 μF and 4 μF is in series with 3 μF across 18 V. Find every voltage and charge.
  4. Can two equal capacitors be assumed to have equal voltage in every network? Explain with a counterexample.
  5. A 2 μF and 8 μF pair is in series across 100 V. Find the voltage across each and identify which faces the greater voltage stress.

For three identical components, Ceq = 9/3 = 3 pF. Q = (3 pF)(120 V) = 360 pC. Each voltage is Q/C = 360/9 = 40 V; three drops sum to 120 V.

Key Takeaways

Key Takeaways

• Identify electrical nodes before identifying series or parallel groups. • Parallel capacitors share voltage and their capacitances add. • A simple initially uncharged series chain shares charge magnitudes. • Series reciprocal capacitances add; the smallest C takes the largest voltage. • Reduce mixed networks, then expand them to recover component states. • Terminal charge is not the sum of every internal plate-charge magnitude. • Check node charge conservation and voltage sums.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…