Skip to lesson content

Lesson 7 of 11

Electrostatic Potential and Capacitance · Lesson 7 of 11

Capacitance and the Parallel-Plate Capacitor

“Derive capacitance from field geometry and explain charge, voltage, units and operating limits.”

Learning Objectives

• Interpret capacitance as a system property rather than stored charge. • Derive the ideal parallel-plate capacitance. • Calculate charge, voltage and electric field consistently. • Recognise fringing and dielectric-breakdown limitations.

Separating charge stores electrical energy

A capacitor consists of two conductors separated by an insulating region. A source transfers electrons from one conductor to the other, creating equal-and-opposite charges in the usual two-terminal configuration. The assembly has net charge zero but contains separated charge and an electric field. The phrase “charge of the capacitor” means the positive magnitude Q on either conductor, not the sum of both conductor charges.

As charge separation grows, the potential difference between the conductors grows too. For fixed geometry in vacuum or a fixed linear dielectric, the field is proportional to Q, and so is its integral giving voltage V. Their ratio is the capacitance. This is a property of geometry, surrounding conductors and dielectric response, rather than a quantity that automatically increases when more charge is supplied.

CapacitanceLaTeX
Here V is the positive plate-to-plate potential difference and Q the corresponding charge magnitude. Capacitance is positive. The constant-ratio model assumes fixed geometry and linear material response. At Q = V = 0, capacitance is defined by the same response law, not by numerically evaluating 0/0.

A farad is a large capacitance for simple separated metal plates. Common subunits are microfarad, 1 μF = 10⁻⁶ F; nanofarad, 1 nF = 10⁻⁹ F; and picofarad, 1 pF = 10⁻¹² F. Do not confuse μF with mF, which means millifarad, 10⁻³ F. For a capacitor with C fixed, doubling Q doubles V. For a fixed required Q, larger C means a smaller voltage.

Derive the field before the capacitance

Take two broad parallel plates with area A and separation d, carrying +Q and −Q in vacuum. If d is much smaller than their lateral dimensions, the central region resembles two infinite sheets. Each sheet contributes field magnitude σ/(2ε₀), with σ = Q/A. Between the plates both fields point from positive to negative, so they add to σ/ε₀. Outside, their fields oppose and cancel in the infinite-sheet approximation.

Parallel plates: fields add insideParallel plates: fields add inside++++−−−−E = Q/(ε₀A)Gap d; overlap area A; edges omittedOutside fields cancel only in the ideal-sheet approximation.
Field addition between oppositely charged plates— Fields add between the plates and approximately cancel outside. The central arrows represent E from +Q to −Q; real finite plates have fringing near edges.
Field, voltage and capacitance of ideal vacuum platesLaTeX
A is plate overlap area in m² and d is separation in m. ε₀ ≈ 8.85 × 10⁻¹² F m⁻¹, so ε₀A/d has units F. The plates are equipotential and the insulating gap has an approximately uniform field away from edges.

Increasing overlap area provides more space for separated charge at the same surface density, so it increases C. Decreasing the gap lowers the voltage produced by a fixed field and charge density, so it also increases C. These statements compare geometry while keeping the dielectric unchanged. If you change d at fixed Q, E remains the same in the ideal model but V changes. If you change d at fixed V, E = V/d and Q both change.

From dimensions to charge

Problem
An air-gap capacitor has A = 6.0 × 10⁻³ m² and d = 3.0 mm. Estimate C, Q and E at 100 V, treating air as vacuum.

  1. 1.Convert d = 3.0 × 10⁻³ m. C = ε₀A/d = (8.85 × 10⁻¹²)(6.0 × 10⁻³)/(3.0 × 10⁻³) = 1.77 × 10⁻¹¹ F = 17.7 pF.
  2. 2.Q = CV = 1.77 × 10⁻⁹ C = 1.77 nC on each plate in magnitude. E = V/d = 3.33 × 10⁴ V m⁻¹.
  3. 3.Checking Q/(ε₀A) gives the same field. A capacitance in pF is reasonable for small separated plates; it is not 17.7 μF.

A single conductor also has a capacitance

An isolated spherical conductor can be treated as a capacitor whose other conductor is infinitely far away. Its surface potential is V = kQ/R relative to infinity, so C = Q/V = R/k = 4πε₀R. Its capacitance grows with radius. Nearby conductors change the field geometry and therefore can change this value; the isolated-sphere expression is not universal for a sphere in every environment.

Isolated sphere in vacuumLaTeX
R is radius in metres; the reference conductor is effectively at infinity, with no nearby objects significantly changing the field.

Limits: edges, leakage and breakdown

Finite plates have curved field lines near edges, called fringing, and nonuniform surface charge there. The infinite-sheet derivation is accurate when separation is small compared with plate dimensions and edge contributions are negligible. It is not exact merely because the plates look parallel. Dielectric strength is the approximate maximum field a material can withstand without substantial conduction or breakdown. It is a field, in V m⁻¹, and differs from dielectric constant K, which is dimensionless.

Estimate a voltage limit

Problem
Use an approximate air breakdown field of 3 × 10⁶ V m⁻¹ for a uniform 1 mm gap. Estimate the corresponding voltage.

  1. 1.V ≈ Ebreak d = (3 × 10⁶)(10⁻³) = 3 × 10³ V. The result is a rough model estimate, not a component voltage rating.
  2. 2.Actual breakdown depends on gap size, pressure, humidity, geometry and surface conditions; local field enhancement at edges can matter. Real capacitors have specified ratings and leakage.

Quick Quiz

Quiz

Quick check

A capacitor with plate charges +Q and −Q has total charge

Explanation

The quoted capacitor charge Q denotes magnitude on one plate; the two charges sum to zero.

Quick check

For fixed linear geometry, doubling Q causes

Explanation

Q = CV with constant capacitance makes voltage proportional to charge.

Quick check

If plate area doubles and separation halves, C becomes

Explanation

C = ε₀A/d gains a factor 2/(1/2) = 4.

Quick check

Between two ideal oppositely charged sheets, field magnitude is

Explanation

Each sheet contributes σ/(2ε₀); both fields point the same way inside.

Quick check

Which conversion is correct?

Explanation

The prefixes micro, nano and pico represent 10⁻⁶, 10⁻⁹ and 10⁻¹² respectively.

Practice Problems

Practice Problems
  1. A 40 pF capacitor is connected to 150 V. Find charge magnitude on either plate and total net charge.
  2. Derive ideal parallel-plate capacitance starting from the field of one sheet.
  3. At fixed charge, double the separation of an isolated vacuum capacitor. State the changes in C, E and V.
  4. Estimate isolated-sphere capacitance for R = 0.09 m using k = 9 × 10⁹.
  5. A dielectric gap is 0.50 mm and has approximate breakdown field 10⁷ V m⁻¹. Estimate the uniform-gap breakdown voltage and explain one limitation.

Q = CV = (40 × 10⁻¹²)(150) = 6.0 × 10⁻⁹ C = 6 nC. Plates carry +6 nC and −6 nC, so the combined net charge is zero.

Key Takeaways

Key Takeaways

• Capacitor charge Q is the magnitude on one conductor, not total net charge. • For fixed linear geometry, Q = CV with constant positive C. • A vacuum parallel-plate capacitor has C = ε₀A/d. • The internal plate fields add; outside cancellation is an ideal approximation. • At fixed Q, changing separation changes voltage but not the ideal central field. • An isolated sphere has C = 4πε₀R. • Dielectric strength and dielectric constant describe different properties.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…