Electrostatic Potential and Capacitance · Lesson 8 of 11
Dielectric Capacitors: Fixed Charge and Fixed Voltage
“Predict dielectric insertion outcomes from the circuit constraint and derive partial-slab capacitance.”
• Calculate capacitance with full dielectric filling. • Compare fixed-charge and fixed-voltage insertion. • Derive capacitance with a dielectric slab thinner than the gap. • Track free charge, bound charge, field and potential consistently.
The same material, two different experiments
Insert a dielectric fully into a parallel-plate capacitor. Polarisation creates bound surface charge opposing the field of the free plate charge. For fixed free charge Q the field becomes E₀/K and the voltage becomes V₀/K. Since Q has not changed, C = Q/V increases by K. This capacitance increase belongs to the geometry and material; it also occurs when the battery remains connected, but Q and V then behave differently.
Disconnected: plate charge is conserved
Charge a capacitor, disconnect both battery leads so no conducting path joins the plates, and insert a dielectric without allowing charge to leak or touch across the plates. The charge on each plate remains fixed. C increases, V = Q/C decreases and E = V/d decreases. Bound charges appear on the dielectric surfaces but do not change the free charge on the isolated plates. A disconnection that leaves an unintended conducting path would not meet this model.
Connected: the battery holds voltage fixed
Leave an ideal battery connected during the same insertion. Its terminals maintain V. The increased capacitance requires Q = CV to increase by K: additional electrons move through the external circuit. Since d is unchanged, E = V/d is unchanged. The opposing polarisation field still exists, but extra free plate charge compensates for it. Saying that dielectrics always reduce E without specifying the constraint would therefore give the wrong answer here.
| Quantity after full insertion | Isolated plates: Q fixed | Ideal battery connected: V fixed |
|---|---|---|
| Capacitance | KC₀ | KC₀ |
| Free plate-charge magnitude | Q₀ | KQ₀ |
| Potential difference | V₀/K | V₀ |
| Average internal field | E₀/K | E₀ |
| Bound polarisation | Appears | Appears; extra free charge compensates its field |
Problem
A 20 pF capacitor is charged to 120 V. A K = 3 dielectric fully fills the gap. Compare isolated and battery-connected cases.
- 1.Initially Q₀ = C₀V₀ = (20 pF)(120 V) = 2.4 nC. The new capacitance is 60 pF in both cases.
- 2.Isolated: Q = 2.4 nC, V = Q/C = 40 V and E is one-third of its initial value.
- 3.Connected: V = 120 V, Q = (60 pF)(120 V) = 7.2 nC and the average field is unchanged. The battery supplies an additional 4.8 nC to the positive plate in conventional-charge accounting.
A slab thinner than the plate separation
Now a dielectric slab has full plate area A but thickness t smaller than d, leaving total vacuum thickness d − t. Assume the slab faces are parallel to the plates and neglect edges. A Gaussian pillbox crossing the vacuum–dielectric interface has no free charge on that interface. The normal free-charge displacement is therefore the same in both layers, giving Evac = Q/(ε₀A) and Ediel = Q/(Kε₀A). The two voltage drops add because the field is traversed successively through both materials.
Check the limits before trusting the expression. If t = 0, C = C₀. If t = d, C = KC₀. If K = 1, the slab is electrically equivalent to vacuum and C = C₀ at every thickness. For t = 3d/4, substitute to obtain C/C₀ = 4K/(K + 3). The result is smaller than K for finite K > 1 because the remaining vacuum layer still takes a substantial part of the voltage.
Problem
A vacuum capacitor has C₀ = 8 pF. A K = 6 slab covers the full plate area with thickness 3d/4. Find C.
- 1.C/C₀ = d/[d/4 + (3d/4)/6] = 1/(1/4 + 1/8) = 8/3.
- 2.C = (8 pF)(8/3) ≈ 21.3 pF. Full filling would give 48 pF; using that value here would ignore the vacuum layer.
- 3.At fixed free charge, the field in the dielectric is one-sixth of that in the vacuum part. The potential remains continuous across the interface, while its slope changes.
How to decide which field changes
First draw the materials and the electrical connections. Then write the conserved quantity or enforced voltage. Use capacitance to find the remaining charge or voltage and only then determine field. A dielectric at fixed voltage is not unpolarised merely because total E stayed constant; and an isolated capacitor does not lose free charge merely because V decreased. Energy consequences require the same distinction and are developed after the network methods.
Quick Quiz
Quiz
A dielectric completely fills an isolated charged capacitor. Its voltage becomes
Q stays fixed and C becomes KC₀, so V = Q/C decreases by K.
With an ideal battery connected and gap unchanged, full dielectric insertion makes E
V remains fixed, so E = V/d remains fixed in the uniform fully filled model.
The additional free charge at fixed V comes from
The battery exchanges charge with the plates as Q = CV increases.
For a full-area slab of thickness t along E, effective electrical thickness is
The voltage drops of the vacuum and dielectric layers add.
For t = d and K = 1, capacitance is
A K = 1 filling has the same permittivity as vacuum.
Practice Problems
- A 10 pF capacitor at 90 V is disconnected and fully filled with K = 3 material. Find C, Q and V.
- Repeat the preceding situation with the ideal 90 V source still connected.
- A slab of K = 4 fills half the gap thickness over the whole plate area. Find C/C₀.
- A K = 5 dielectric completely fills a gap while plate separation is reduced to half its original value. Find the capacitance ratio.
- For a full-area slab with t = 3d/4 and K = 3, find the fractions of voltage across vacuum and dielectric.
Initially Q = (10 pF)(90 V) = 900 pC. After insertion C = 30 pF, Q remains 900 pC and V = 900/30 = 30 V. The field is one-third of its original value at unchanged gap.
Key Takeaways
• Complete dielectric filling gives C = Kε₀A/d. • Disconnected isolated plates conserve free charge if leakage is negligible. • A connected ideal battery fixes voltage and supplies additional charge. • At fixed Q, full filling reduces V and E by K. • At fixed V and unchanged d, the full-gap field remains V/d. • A full-area partial slab gives C = ε₀A/(d − t + t/K). • Bound polarisation charge is distinct from free plate charge.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…