Skip to lesson content

Lesson 8 of 10

Current Electricity · Lesson 8 of 10

Solving Circuit Networks

“Use conservation of charge and energy to reduce simple networks, set circuit signs and solve networks with multiple sources or symmetry.”

Learning Objectives

• Derive series and parallel resistor rules from current and voltage constraints. • Apply Kirchhoff’s junction and loop rules with explicit signs. • Solve a multi-source network and check unused loops and power. • Use symmetry to find the body-diagonal resistance of a resistor cube.

First identify nodes and genuine series or parallel connections

A circuit drawing is a map of connections, not a map of physical distances. Points joined by ideal wire share potential. Two resistors are in series only if their common junction has no other current path, so they carry the same current. Two resistors are in parallel only if both ends connect to the same two nodes, so they have the same voltage. Similar appearance on the page is insufficient. Redraw with node labels before reducing a complicated network.

Resistor combinations derived from constraintsLaTeX
In series, voltage drops add at common I. In parallel, branch currents add at common V. Positive parallel equivalent resistance is smaller than every individual branch resistance.
Reduce before solving

Problem
A 2 Ω resistor is in series with a parallel pair of 3 Ω and 6 Ω. A 12 V ideal source powers the combination. Find all currents.

  1. 1.The parallel pair has resistance (3 × 6)/(3 + 6) = 2 Ω. Total resistance is 4 Ω and source current is 3 A.
  2. 2.The series resistor drops 3 × 2 = 6 V, leaving 6 V across the parallel pair. Its currents are 6/3 = 2 A and 6/6 = 1 A.
  3. 3.The branch currents add to 3 A. Total heat is 3² × 2 + 2² × 3 + 1² × 6 = 36 W, equal to 12 × 3 W.

Charge conservation gives the junction rule

Kirchhoff’s junction rule in a steady circuitLaTeX
Currents are signed scalars relative to assigned branch arrows. More generally incoming minus outgoing current is dQ_node/dt; the steady rule assumes no continuing charge accumulation.

If 5 A enters a junction and one outgoing branch is assigned 2 A, the remaining outgoing current must be 3 A. The angles between the wires do not enter this accounting. If you instead assign its arrow inward, its value is −3 A. Negative current does not invalidate the solution; it corrects the initial reference direction. At an unbranched point the same rule ensures equal steady current on both sides, even across different materials or areas.

Potential consistency gives the loop rule

Kirchhoff’s loop rule for the present DC modelLaTeX
Use electrostatic/quasistatic lumped circuits without an unmodelled changing magnetic flux through the loop. At later stages an induced emf must be included when relevant.

Potential has one value at each node. Traversing a closed path and returning to the start must give zero net potential change in this model. This is also energy accounting per unit charge: source rises balance resistive drops. Choose any traversal direction independently of your branch current arrows. Across a resistor along its assigned current use −IR; against it use +IR. Across an ideal emf from negative to positive use +ε; from positive to negative use −ε. If a real cell is represented by ε and r, include its internal resistor as another resistive drop or rise.

TraversalPotential changeReason
Resistor along current arrow−IRPotential falls along positive current
Resistor against current arrow+IRPotential rises on reverse traversal
Ideal cell − to ++εSource raises electric potential
Ideal cell + to −−εReverse traversal gives the opposite rise

Choose enough independent equations, not every imaginable loop. For a connected network with N nodes and B branches, N − 1 independent junction equations and B − N + 1 independent loop equations suffice when branch definitions are consistent. Extra loop equations should become checks. Avoid giving independent currents to every resistor in a clearly unbranched chain; use the junction rule first to reduce unknowns.

Two sources feeding one load

Problem
Between nodes P and N are a 12 V source with 2 Ω series resistance, a 6 V source with 2 Ω series resistance and a 4 Ω load. Both source positive terminals face P. Find branch currents.

  1. 1.Set V_N = 0 and V_P = V. Assign each source current toward P and load current from P to N. Junction equation: (12 − V)/2 + (6 − V)/2 = V/4.
  2. 2.Multiplying by four gives 24 − 2V + 12 − 2V = V, so V = 7.2 V. Source currents are 2.4 A and −0.6 A, and load current is 1.8 A.
  3. 3.The 6 V source receives current. Net emf supply is 12(2.4) + 6(−0.6) = 25.2 W. Heat is 2(2.4²) + 2(0.6²) + 4(1.8²) = 25.2 W.

A network with no obvious resistor reduction

Two sources: polarities and node labels define the circuit4 Ω4 Ω2 Ω2 Ω10 V+−1 Ω+−5 VABCD
Two-source network used below— The centre branch contains a 10 V ideal source, positive toward A, and a 1 Ω resistor. The right branch is a 5 V ideal source, positive toward B. All other branches contain the labelled resistors.
Solve currents before interpreting the zero branch

Problem
For the displayed network take I₁ from C to A, I₂ from A to B and I₃ from D to B through the 5 V source. Find all branch currents.

  1. 1.Junctions give A→D current I₁ − I₂, B→C current I₂ + I₃, and C→D current I₂ + I₃ − I₁. Loop A→D→C→A gives 10 − 4(I₁ − I₂) + 2(I₂ + I₃ − I₁) − I₁ = 0, or 7I₁ − 6I₂ − 2I₃ = 10.
  2. 2.Loop A→B→C→A gives 10 − 4I₂ − 2(I₂ + I₃) − I₁ = 0, or I₁ + 6I₂ + 2I₃ = 10. Loop D→B→C→D gives 5 − 2(I₂ + I₃) − 2(I₂ + I₃ − I₁) = 0, or 2I₁ − 4I₂ − 4I₃ = −5.
  3. 3.Add the first two equations to obtain 8I₁ = 20, so I₁ = 2.5 A. The second now gives 3I₂ + I₃ = 3.75; the third gives I₂ + I₃ = 2.5. Subtract to find I₂ = 0.625 A and I₃ = 1.875 A.
  4. 4.Therefore C→A is 2.5 A, A→B is 0.625 A, A→D is 1.875 A, B→C is 2.5 A and C→D is zero. Zero current here is a derived equal-potential result, not permission to discard the branch before solving. A further loop A→B→D→A gives −4(0.625) − 5 + 4(1.875) = 0, independently checking signs.

Symmetry can replace a long equation list

Consider a cube made from twelve equal resistors R, driven between opposite body-diagonal vertices A and G. Rotations about that diagonal exchange the three neighbours of A while leaving the electrical problem unchanged. Those neighbours must have equal potential. The three neighbours of G form a second equal-potential group. Grouping equal-potential nodes does not send current through extra real wires; it is a mathematical simplification justified by symmetry and the identical component values.

Body-diagonal cube resistanceLaTeX
The groups are connected by three equal edges, then six equal edges, then three equal edges. If source current is I_total, each outer-group edge carries I_total/3 and each middle edge I_total/6.
Cube driven across opposite body-diagonal verticesAgroup 1group 2GR/3R/6R/33 edges6 edges3 edges
Equipotential groups of a resistor cube— This is an equivalent circuit of grouped cube vertices, not a drawing of the cube itself. Equality of potential must be justified by the original cube symmetry.
Cube edge currents

Problem
Every cube edge is 1 Ω and 10 V is applied across its body diagonal. Find equivalent resistance and edge currents.

  1. 1.R_eq = 5/6 Ω, so total current is 10/(5/6) = 12 A.
  2. 2.Each of the three edges leaving the positive vertex carries 4 A, each of the six middle edges 2 A and each of the three entering the negative vertex 4 A.
  3. 3.A three-edge route drops 4 × 1 + 2 × 1 + 4 × 1 = 10 V. Total heat is 6(4² × 1) + 6(2² × 1) = 120 W, equal to 10 × 12 W.

Before accepting any circuit result, check node currents, one unused loop, power conservation and a limiting case. Predict breaking one cube edge: the original rotational symmetry is lost, so the grouped-node result need not remain valid. A symmetric-looking outline alone is never enough.

Quick Quiz

Quiz

Quick check

Two resistors are definitely in parallel when

Explanation: Parallel is a connection condition that imposes equal voltage.

Quick check

Crossing a resistor along its assigned current gives

Explanation: Potential falls in the direction of positive conventional current through a passive resistor.

Quick check

A branch current solved as −3 A means

Explanation: The arrow was a reference; its sign reports the actual direction.

Quick check

The steady junction rule follows from

Explanation: Net incoming charge cannot continue building up in a steady node.

Quick check

Twelve equal cube-edge resistors R have body-diagonal resistance

Explanation: Symmetry gives equivalent stages R/3, R/6 and R/3.

Practice Problems

Practice Problems
  1. A 5 A current enters a node. One branch leaves with 1.5 A; another is assigned inward current x. Find x.
  2. A 9 V ideal source drives series 2 Ω and 4 Ω resistors. Traverse the loop first with and then against current and verify the sum.
  3. In the displayed two-source network verify source power against resistor heat using the solved currents.
  4. Derive the cube result by writing a three-edge path in terms of the current i in an edge leaving the positive vertex.
  5. A parallel 4 Ω and 12 Ω pair is in series with 3 Ω across 18 V. Find all currents and check power.

Use incoming = outgoing: 5 + x = 1.5. Thus x = −3.5 A, meaning 3.5 A actually leaves along that branch. Treat currents as signed scalars, not vectors based on wire angles.

Key Takeaways

Key Takeaways

• Identify electrical nodes before recognising series and parallel connections. • Steady junction equations express conservation of charge. • Loop equations express potential consistency and energy accounting. • Resistor signs depend on traversal relative to the assigned current. • Source signs depend on traversal relative to marked polarity. • Negative currents reverse reference arrows without invalidating the method. • Symmetry can group equal-potential nodes only when the whole electrical problem shares it. • Unused loops and power balance provide independent checks.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…