Current Electricity · Lesson 5 of 10
Electrical Energy and Power
“Follow energy per charge through a circuit, derive Joule heating and distinguish fixed-current from fixed-voltage power comparisons.”
• Derive electrical power from potential-energy transfer. • Apply the correct power expression with stated voltage and current constraints. • Calculate energy use and distinguish power, energy and charge. • Explain high-voltage transmission through current and cable-loss calculations.
The resistor consumes energy, not charge
A heater can carry the same steady current into and out of its element while its temperature rises. There is no contradiction: charge is conserved, whereas electrical potential energy is transferred into internal energy and then to the surroundings. Think of a small positive charge ΔQ moving through a passive resistor from higher potential V_A to lower potential V_B. Its electric potential-energy change is ΔQ(V_B − V_A). If the positive drop is V = V_A − V_B, the decrease has magnitude VΔQ.
The voltage tells us joules transferred per coulomb; the current tells us coulombs transferred per second. Multiplying cancels coulombs and gives joules per second. In a source, chemical processes can supply energy to charges rather than absorb it as heat. A motor can convert much of its input into mechanical work. Therefore VI is not automatically a heating rate for every electrical device. For a simple resistive element, directed energy is scattered into microscopic material motion and eventually leaves as heat or radiation. The mean drift kinetic energy need not grow continuously.
Joule heating and the controlled quantity
Increasing resistance has no unique power consequence until a constraint is named. At fixed current, a larger resistance needs a larger voltage and absorbs more power, I²R. At fixed voltage, it carries less current and absorbs less power, V²/R. In series resistors the common current makes the larger resistor dissipate more; in parallel resistors the common voltage makes the smaller resistor dissipate more. These statements are compatible because the circuit imposes different common quantities.
Problem
Compare power in 3 Ω and 6 Ω resistors when connected first in series and then in parallel across an ideal 12 V source.
- 1.In series, total resistance is 9 Ω and current is 12/9 = 4/3 A. Powers are (4/3)² × 3 = 16/3 W and (4/3)² × 6 = 32/3 W; total 16 W.
- 2.In parallel, branch powers are 12²/3 = 48 W and 12²/6 = 24 W; total 72 W.
- 3.The 6 Ω resistor dissipates more in series, while the 3 Ω resistor dissipates more in parallel. The source supplies different total currents in the two arrangements.
Watts, joules and kilowatt-hours
Power is a rate, energy is a quantity transferred and charge is a quantity transported. A 1 kW device running for one hour transfers 1 kWh of energy: 1000 J/s × 3600 s = 3.6 × 10⁶ J. A kilowatt-hour is not a unit of power and is unrelated to an ampere-hour unless the source voltage is also specified. An ampere-hour measures 3600 C of charge. At a constant 12 V, an ideal transfer of 1 Ah corresponds to 12 Wh, but changing terminal voltage alters the energy per unit charge.
Problem
A 230 V heater absorbs 920 W steadily for 15 min. Find current, hot resistance and electrical energy.
- 1.I = P/V = 920/230 = 4.0 A. R = V/I = 57.5 Ω at that operating temperature.
- 2.Time is 900 s, so W = Pt = 920 × 900 = 8.28 × 10⁵ J.
- 3.In billing units the same energy is 0.920 kW × 0.25 h = 0.230 kWh. These are two units for the same energy, not two different losses.
Why transmit a specified power at high voltage?
A long cable has resistance R_c, including both outgoing and return conductors when relevant. Suppose useful power P_L is to reach a load at voltage V_L. Its current is P_L/V_L. The cable carries that current and loses I²R_c as heat. If the same useful power can be delivered at a higher load-side transmission voltage, less current is required and cable losses decrease. Comparing at equal current would answer a different question.
Problem
Deliver 10 kW to a load through total cable resistance 2.0 Ω. Compare load voltages 1.0 kV and 10 kV.
- 1.At 1.0 kV, I = 10 A and cable loss is 10² × 2.0 = 200 W. Cable drop is 20 V, so the source must provide 1020 V and 10.2 kW.
- 2.At 10 kV, I = 1.0 A and cable loss is 2.0 W. Cable drop is 2.0 V, so the source must provide 10002 V and 10.002 kW.
- 3.A tenfold voltage increase at equal delivered power gives a hundredfold reduction in resistive cable loss. The source and load voltages are not exactly equal when loss is finite.
The practical system must also handle insulation, safe operating limits and voltage conversion. Transformers in AC systems allow useful changes of voltage and current; their detailed operation belongs to later study. Here the important causal chain is fixed delivered power → higher voltage → lower current → lower I²R cable loss. Saying that high voltage alone reduces every power loss, without holding useful power fixed, would be incomplete.
An energy check is stronger than a formula match
For a steady purely resistive network, sum the heating rates of all resistors and compare with total power supplied by sources. Any mismatch suggests an incorrect current, a missing internal resistance or inconsistent signs. Predict adding resistance at fixed source voltage: total power from an ideal voltage source decreases for a single series load, while a given resistor’s share may change. Analyse the actual circuit before using a proportional slogan.
Quick Quiz
Quiz
A steady current enters and leaves a resistor unchanged because
Explanation: The resistor converts electrical energy; it does not steadily destroy charge.
At fixed current, doubling R makes its heating power
Explanation: P = I²R with I fixed.
At fixed voltage, doubling R makes its heating power
Explanation: P = V²/R with V fixed.
One kilowatt-hour equals
Explanation: It is energy: 1000 J/s multiplied by 3600 s.
At equal delivered power, tripling line voltage gives resistive cable loss approximately
Explanation: The current falls by three, so I²R falls by nine when cable resistance is unchanged.
Practice Problems
- A 10 Ω resistor carries 2.0 A for 60 s. Find voltage, power and dissipated energy.
- A 100 W, 200 V resistive device is operated at 100 V. Estimate power assuming unchanged resistance.
- A cable loses 80 W while transmitting a fixed load power. What loss results if transmission voltage doubles with the same R_c?
- A device transfers 0.50 kWh in 20 min at 250 V steadily. Find mean power, current and charge transfer.
- Why can two identical currents in a source and resistor correspond to opposite energy roles?
Using the resistor’s operating resistance, V = IR = 20 V. Power is I²R = 4 × 10 = 40 W. At constant current for 60 s, energy is 40 × 60 = 2400 J. This is energy transferred, while the charge transported is separately It = 120 C.
Key Takeaways
• Voltage is energy transfer per charge; current is charge transfer per time. • Power is VI with a consistent sign convention. • A resistor dissipates electrical energy while conserving charge. • Use I²R at fixed current and V²/R at fixed voltage. • A kilowatt-hour is energy; an ampere-hour is charge. • At fixed delivered power, higher transmission voltage lowers current and resistive cable loss. • Check source power against every resistive loss.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…