Skip to lesson content

Lesson 10 of 10

Current Electricity · Lesson 10 of 10

Chapter Summary and Practice

“Connect microscopic transport, material response, energy transfer and circuit conservation through a complete conditional reference and mixed practice.”

Learning Objectives

• Connect carrier drift to current, resistance, material properties and electrical power. • Select formulas with the correct fixed quantities and validity conditions. • Solve real-source and bridge networks with consistent signs and energy checks. • Identify and correct common conceptual errors across the chapter.

One chapter, four connected levels

Current electricity can be viewed at four levels. Microscopically, mobile charges respond to a field and scatter, producing a small mean drift. At the material level, conductivity relates local field to current density. At the component level, geometry and material response give resistance, while sources supply energy per charge. At the network level, charge conservation and potential consistency determine currents and voltages. A complete solution moves between these levels only when the needed assumptions are justified.

For example, a lamp need not wait for electrons to drift from a battery. The circuit already contains carriers; a rapidly propagating field change establishes their local response. A neutral wire can carry current because its positive and negative charges need not have the same velocities. Its resistor transfers energy rather than using up current. A source’s emf specifies an energy-per-charge contribution; load and internal resistance determine how much current flows.

Choose a method before calculating

Given situationStart withEssential condition or check
Charge transferred or an I–t graphI = dQ/dt or signed graph areaChoose section orientation and time interval
Carrier density, area and currentI = neAv_dUniform single-carrier transport; distinguish speed and vector
Wire material and dimensionsR = ρL/AUniform geometry; actual temperature; contacts neglected
Heating or energy useP = VI, W = ∫PdtName the device and what voltage/current belongs to it
Real cell and loadV = ε − Ir, I = ε/(R+r)Positive I denotes discharge; reverse its sign for charging
Several sources or a bridgeNode/loop conservationMark polarities and branch references first
Symmetric cubeEqual-potential groupsAll component values and source placement preserve symmetry

Conditional formula reference

RelationMeaning and symbolsUnits and conditions
I = dQ/dt; Q = ∫I dtSigned charge rate and cumulative transferI: A; Q: C; t: s; signed orientation
𝐣 = nq𝐯_d; I = ∫𝐣·d𝐀Local carrier charge flux and surface currentj: A/m²; n: m⁻³; q: C; v_d: m/s
𝐯_d = −(eτ/m)𝐄; μ = eτ/mElectron response in relaxation modelμ: m²/(V s); τ: s; weak-field model
σ = neμ; ρ = 1/σMaterial responseσ: S/m; ρ: Ω m; specified state
R = ρL/A; V = IRSample geometry and ohmic responseR: Ω; L: m; A: m²; constant state
R(T) ≈ R₀[1 + α(T − T₀)]Temperature approximationα: K⁻¹; reference and fit interval stated
P = VI; P_R = I²R = V²/RElectrical transfer and resistor heatingP: W; W_energy = Pt only if steady
V = ε − Ir; V_ch = ε + I_crDischarge and charging terminal voltagesε,V: V; r: Ω; I,I_c: A with stated signs
ε_eq = Σsₖεₖ; r_eq = ΣrₖSeries sourcesSigned emfs; positive internal resistances
r_eq = 1/Σ(1/rₖ); ε_eq = r_eqΣ(εₖ/rₖ)Parallel sourcesFinite rₖ; common terminal orientation
ΣI_in = ΣI_out; ΣΔV_loop = 0Circuit conservationSteady charge; no omitted induced emf
P_arm/Q_arm = R_arm/S_armBridge null with stated arm labelsNonzero supply, finite positive arms and functioning detector

The symbol P is often used both for power and for a bridge arm resistance. Context and units distinguish them; the table explicitly labels bridge arms. Likewise ρ here is resistivity, not charge density, and A can mean area while the upright A denotes ampere. A numerical expression with units is easier to audit than a bare number.

Rebuild the main derivations

To obtain the current–drift relation, count nAv_dΔt net carrier transfers and divide charge neAv_dΔt by time. To obtain conductivity, average the electron response under acceleration −e𝐄/m over a relaxation time τ, then multiply drift by negative electron charge density. Two minus signs make current density parallel to field. To connect that local law to a sample, substitute E = V/L and j = I/A into E = ρj. Every step introduces conditions: statistical averaging, a transport model and uniform geometry are distinct assumptions.

Energy transfer follows from VΔQ, giving VI per second. For a real cell, the emf supplies εI while internal resistance dissipates I²r, leaving terminal power VI. For charging, current enters the positive terminal and the terminal input must cover both storage-related emf power and heat. Series-source equivalence follows from adding potential changes along the same current path; parallel-source equivalence follows from adding branch currents at a common voltage. Bridge balance follows from equal midpoint potentials and cancellation of common current factors or supply voltage.

Misconceptions to replace with testable reasoning

Misleading claimA better explanation
A battery always gives one fixed currentCurrent depends on the full load and internal source behaviour
Current is used up in a resistorSteady charge flow continues; energy is converted
All charges move with conventional currentElectron drift in metal is opposite; ionic carriers need separate signs
V/I at one point proves Ohm’s lawTest proportionality over a range at fixed conditions
A larger resistance always gives more heatAt fixed I, yes; at fixed V, less heat
A neutral wire cannot carry currentOpposite charge populations can have different mean velocities
An open parallel-cell output means every cell is idleUnequal emfs can drive circulating branch current
Any zero detector reading proves bridge balanceCheck connectivity, source and detector sensitivity

A worked connection from source to carriers

A loaded cell and a copper lead

Problem
A 6.0 V cell with r = 0.20 Ω drives a 2.8 Ω external load, whose resistance includes its leads. One copper lead has area 1.0 mm² and n = 8.5 × 10²⁸ m⁻³. Find current, terminal voltage, lead drift speed and the source power split.

  1. 1.Total resistance is 3.0 Ω, so I = 2.0 A. V = 6.0 − 2.0 × 0.20 = 5.6 V across the full external load.
  2. 2.Convert lead area to 1.0 × 10⁻⁶ m². v_d = 2.0/[(8.5 × 10²⁸)(1.60 × 10⁻¹⁹)(1.0 × 10⁻⁶)] = 1.47 × 10⁻⁴ m/s, opposite conventional current.
  3. 3.The ideal emf supplies 12 W. Internal heat is 0.80 W and external power 11.2 W, which add correctly. Do not assign the whole 5.6 V to the copper lead alone; it is the voltage of the complete external load.

An unbalanced bridge with a series supply resistance

10 Ω5 Ω5 Ω10 Ω5 Ω10 Ω10 V+−ABCD
Network for the worked problem and mixed practice— The centre 5 Ω is a resistor rather than a galvanometer. The bottom 10 Ω resistor is in series with the 10 V source; it is not one of the four bridge arms.
Solve the bridge and then the source

Problem
For the displayed arm values let a 10 V ideal source drive the A–C bridge through an additional series resistor of 10 Ω. Find all six branch currents.

  1. 1.Set V_C = 0 and V_A = V, the unknown bridge voltage. At B, (V_B − V)/10 + V_B/5 + (V_B − V_D)/5 = 0, giving 5V_B − 2V_D = V. At D, (V_D − V)/5 + V_D/10 + (V_D − V_B)/5 = 0, giving −2V_B + 5V_D = 2V.
  2. 2.Multiply the first equation by 5 and the second by 2, then add: 21V_B = 9V, so V_B = 3V/7. Substitution gives V_D = 4V/7. Source current is (V − V_B)/10 + (V − V_D)/5 = 4V/70 + 3V/35 = V/7. Thus the bridge equivalent is 7 Ω.
  3. 3.Total series resistance is 10 + 7 = 17 Ω, so source current is 10/17 A and bridge voltage V = 70/17 V. Node potentials are V_B = 30/17 V and V_D = 40/17 V.
  4. 4.Branch currents are A→B = 4/17 A, B→C = 6/17 A, A→D = 6/17 A, D→C = 4/17 A and D→B = 2/17 A. The external branch returns C→A at 10/17 A. At B, 4/17 + 2/17 = 6/17; at D, 6/17 = 4/17 + 2/17.
  5. 5.Bridge power is (10/17)² × 7 = 700/289 W; the source series resistor dissipates 1000/289 W. Their sum is 1700/289 = 100/17 W, equal to 10 × (10/17). The source emf is not the bridge terminal voltage.

A final habit: assumptions, signs and limits

Write the model conditions before using its convenient formulas. Track dimensions, retain intermediate precision and explain each negative sign. Check a node, an unused loop, total power and a useful limit. As a load tends to open circuit, current should approach zero and a simple cell’s terminal voltage approach emf. At an ideal bridge null the detector current should vanish without forcing arm currents to vanish. As n or area increases at fixed current, the required drift speed should decrease. These checks reveal mistaken reasoning that a familiar-looking final number can hide.

Quick Quiz

Quiz

Quick check

A source terminal voltage exceeds its relaxed emf in the simple model when

Explanation: Positive charging current requires terminal voltage ε + I_cr.

Quick check

Which pair correctly gives material and sample units?

Explanation: Material resistivity and sample resistance differ by geometry.

Quick check

A bridge is balanced but arm currents are nonzero. This is

Explanation: Only the detector branch has zero current at an ideal null.

Quick check

At unchanged n and I, doubling conductor area makes drift speed

Explanation: The product Av_d must remain constant.

Quick check

The most useful final check for a multi-source resistive network is

Explanation: Some currents may reverse and some sources may absorb power; total energy balance must still hold.

Practice Problems

Practice Problems
  1. A steady 2.5 A current flows for 4 min. Find charge and the number of electron charges transported.
  2. Find drift speed for I = 3 A, n = 8.5 × 10²⁸ m⁻³ and A = 2 × 10⁻⁶ m², and estimate drift time over 3 m.
  3. A 15 m uniform wire has A = 6.0 × 10⁻⁷ m² and R = 5 Ω. Find ρ and predict R if L triples at constant volume and unchanged material state.
  4. A silver wire has R = 2.1 Ω at 27.5 °C and 2.7 Ω at 100 °C. Find the interval coefficient referenced to 27.5 °C.
  5. An element rises from 100 Ω at 27 °C to 117 Ω. Estimate temperature with α = 1.70 × 10⁻⁴ °C⁻¹ and state the assumption.
  6. A 230 V heater’s current settles from 3.2 A at 27 °C to 2.8 A. Estimate temperature with the same α and compare initial and final power.
  7. A 10 V cell with internal resistance 3 Ω delivers 0.50 A. Find load R, terminal V and the power split.
  8. Calculate the constant-r short-circuit current for a 12 V, 0.40 Ω source. Why can zero terminal voltage still accompany substantial heating?
  9. An 8 V storage cell with r = 0.50 Ω is charged from 120 V through 15.5 Ω. Find charging current and terminal V.
  10. Two parallel cells each have r = 1 Ω, with emfs 2 V and 1 V. A 2 Ω load is attached. Find currents and explain the negative branch.
  11. In the unbalanced bridge worked above, verify all branch currents from node voltages and determine the direction of its central current.
  12. A cube with every edge 6 Ω is driven across its body diagonal at 15 V. Find total current and each class of edge current, then check power.

Time is 240 s. Charge transfer is It = 2.5 × 240 = 600 C. The net electron-charge count is 600/(1.60 × 10⁻¹⁹) = 3.75 × 10²¹. The number counts net transfers, not newly created electrons.

Key Takeaways

Key Takeaways

• Connect microscopic drift, material response, component behaviour and circuit conservation. • Separate current, charge, voltage, resistance, resistivity, power and energy by meaning and units. • Every formula carries assumptions about material state, geometry or source constraints. • Electron drift direction and conventional current direction differ in metals. • Use consistent terminal labels and signed currents for discharge and charging. • Use actual load voltage rather than substituting source emf without checking drops. • A bridge null is an equal-potential condition; unbalanced bridges require full circuit analysis. • Check charge balance, loop potentials, dimensions, limits and total power.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…