Current Electricity · Lesson 4 of 10
Materials and Temperature
“Explain how carrier density and scattering shape material resistivity, and use temperature coefficients with explicit reference conditions.”
• Compare conductors, alloys, semiconductors and insulators by transport behaviour. • Use the limited-range linear temperature relation correctly. • Infer temperature or a coefficient from resistance measurements. • Explain heating transients and limits of extrapolation.
Material classes span many orders of magnitude
A metal wire and an equally shaped rubber strip can have enormously different resistances. The geometry is the same; the available carriers and their mobility are not. Good metals commonly have resistivities of order 10⁻⁸ to 10⁻⁶ Ω m near room temperature. Semiconductors lie over a broad, strongly condition-dependent range. Insulators can have resistivities many orders of magnitude higher. These are behaviour ranges, not immutable boundaries: temperature, impurities, moisture, illumination and electric field can change a material’s response.
Semiconductor doping introduces controlled impurities that change carrier populations. It is not the same as simply adding more scattering centres to a metal. In metals, alloying often increases scattering and resistivity; many resistance alloys combine appreciable resistivity with a small temperature coefficient. Nichrome is useful in heaters; manganin and constantan are useful where resistance should vary little with temperature. No universal table value should replace the actual material state given in a problem.
Why warming can have opposite effects
Recall ρ = m/(ne²τ) in the simple transport model. In an ordinary metal over a moderate temperature range, n changes relatively little, while increased lattice vibrations cause stronger momentum scattering and shorten τ. Resistivity usually rises. It is more accurate to emphasise the changing scattering of conduction electrons from the vibrating lattice than to say all metallic electron speeds simply follow a classical thermal-gas law.
In an intrinsic semiconductor, warming can produce many more mobile electrons and holes. The increase in carrier population can dominate a reduction in mobility, so resistivity falls. Doped semiconductors can have several temperature regimes, so do not state that every semiconductor must show the same trend at every temperature. High-resistivity insulators can also become more conducting when thermally activated carriers are available. The microscopic balance, rather than the label alone, determines the result.
A straight-line approximation near a reference temperature
This is a local straight-line approximation to the material curve. The slope dρ/dT near T₀ divided by ρ(T₀) defines α at that reference. It is a fractional change per degree, not an extra resistance in ohms per degree. A Celsius temperature difference has the same numerical size as a kelvin difference, so either can be used here. Absolute-temperature formulas elsewhere may require kelvin; do not transfer this convenience to every thermal equation.
A metal’s full low-temperature curve need not remain straight. Impurities and defects can give residual resistivity, and some materials become superconducting under appropriate conditions. Extrapolating a room-temperature straight line until it predicts negative resistivity is a misuse of the approximation. Likewise, a coefficient averaged over a heater’s large temperature range is an explicitly supplied effective value, not proof that the material is exactly linear over that whole interval.
Problem
A silver wire is 2.1 Ω at 27.5 °C and 2.7 Ω at 100 °C. Estimate α referenced to 27.5 °C.
- 1.ΔR = 0.6 Ω and ΔT = 72.5 °C. Thus α = 0.6/(2.1 × 72.5) = 3.94 × 10⁻³ °C⁻¹.
- 2.The same absolute straight-line slope is 0.6/72.5 = 8.28 × 10⁻³ Ω/°C. Referencing that line at 100 °C gives 8.28 × 10⁻³/2.7 = 3.07 × 10⁻³ °C⁻¹.
- 3.The coefficients differ because the denominator is a different reference resistance; the fitted straight line is the same.
A heater approaches thermal balance
A cold heating element usually draws more current than the same element when hot, at a fixed supply voltage and positive temperature coefficient. Electrical input raises its temperature; heat loss to the surroundings also grows. A steady temperature is reached when input power equals the rate of energy loss. This does not mean no energy is flowing. It means stored thermal energy is no longer increasing. Small measuring currents are used for the cold resistance so that the measurement itself produces negligible heating.
Problem
An element is 75.3 Ω at 27.0 °C. At 230 V its settled current is 2.68 A. Use an average α = 1.70 × 10⁻⁴ °C⁻¹.
- 1.The hot resistance is 230/2.68 = 85.8209 Ω. The rise is (85.8209/75.3 − 1)/(1.70 × 10⁻⁴) = 821.9 °C.
- 2.The estimated final temperature is 848.9 °C, or about 8.5 × 10² °C at the data precision. Rounding hot resistance to 85.8 Ω earlier gives about 847 °C; the difference is a rounding effect, not different physics.
- 3.At steady temperature the supply still delivers 230 × 2.68 ≈ 616 W, balanced by heat loss. The large-range estimate depends on the supplied average coefficient.
Problem
A platinum sensor reads 5.000 Ω at 0 °C and 5.230 Ω at 100 °C. Its bath resistance is 5.795 Ω. Estimate temperature using the specified linear calibration.
- 1.The calibration slope is (5.230 − 5.000)/100 = 0.00230 Ω/°C.
- 2.The bath rise from the ice point is (5.795 − 5.000)/0.00230 = 345.65 °C, about 346 °C.
- 3.This extrapolates beyond the two calibration points. It is the answer for the assumed linear model; precision thermometry would require an appropriate calibrated curve over the bath range.
Predict warming an ohmic wire while maintaining constant current rather than voltage. With positive α the resistance increases, so V = IR increases and heating I²R increases. At fixed voltage, by contrast, current and V²/R decrease as R rises. There is no contradiction: the external control is different.
Quick Quiz
Quiz
For ordinary metals near room temperature, increasing T usually
Explanation: Lattice-vibration scattering generally increases while the mobile carrier density changes comparatively little.
The units of α are
Explanation: α multiplies a temperature difference to give a dimensionless fractional change.
A 100 Ω resistor has α = 0.004 K⁻¹. A 10 K rise gives approximately
Explanation: R = 100[1 + 0.004 × 10] = 104 Ω.
A semiconductor can become less resistive on warming because
Explanation: Increasing carrier density can outweigh decreasing mobility in the relevant temperature regime.
Extrapolating a metal’s local linear law to negative resistivity indicates
Explanation: A limited-range fit must not be extended beyond its physical validity.
Practice Problems
- A 100 Ω element at 27 °C becomes 117 Ω. Use α = 1.70 × 10⁻⁴ °C⁻¹ to estimate temperature.
- At 230 V, an element initially draws 3.2 A at 27 °C and later 2.8 A. Estimate settled temperature with α = 1.70 × 10⁻⁴ °C⁻¹.
- A resistor has α = 0.003 K⁻¹ at 20 °C. Find its resistance ratio after warming to 70 °C and its fitted coefficient referenced to 70 °C.
- Explain why a low temperature-coefficient alloy can still be a useful heating material.
- For a positive-coefficient resistor, compare heating trends as T increases at fixed I and at fixed V.
Rearrange R/R₀ − 1 = α(T − T₀). The rise is 0.17/(1.70 × 10⁻⁴) = 1000 °C, so T = 1027 °C. This large-range result assumes the stated coefficient is an appropriate average and expansion is negligible.
Key Takeaways
• Material resistivity depends on carrier populations and scattering as well as temperature. • Most ordinary metals have positive temperature coefficients over moderate ranges. • Semiconductor trends depend on the balance of carrier density and mobility. • The linear temperature law is an approximation tied to a reference and interval. • Temperature differences may use kelvin or Celsius degrees with matching coefficients. • Heater temperature estimates depend on the stated effective coefficient. • A steady thermal state balances continuing input power and heat loss.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…