Skip to lesson content

Lesson 3 of 10

Current Electricity · Lesson 3 of 10

Resistance and Ohm’s Law

“Distinguish an empirical proportionality from a resistance ratio, connect sample geometry to resistivity and interpret nonlinear device graphs.”

Learning Objectives

• Test Ohm’s law at fixed physical conditions and interpret graph slopes. • Derive resistance scaling with length and cross-sectional area. • Connect macroscopic resistance to local field and current density. • Recognise nonlinear, asymmetric and negative-differential characteristic curves.

A relationship to test, not a universal definition

Suppose a variable low-voltage source drives a wire. Increase its potential difference in steps and measure the steady current. Many wires at constant temperature give a straight-line relation through the origin: doubling voltage doubles current. This is Ohm’s law. Its conditions matter: heating, strain, changing carrier density or a sufficiently strong field can change the response. An incandescent filament measured while its temperature rises need not give a straight line even though its material has a nearly ohmic response at each fixed temperature.

Ohm’s law for a fixed stateLaTeX
V is the potential drop in the current direction across the resistor, in volts; I is in amperes and R in ohms (Ω = V A⁻¹). A constant ratio over the investigated range is the substantive empirical claim.

At one nonzero-current operating point one can define a ratio R = V/I for a conducting device. That ratio alone does not establish Ohm’s law: it may change with voltage, current, direction or state. A voltage-versus-current graph has slope R for an ohmic resistor; a current-versus-voltage graph has slope 1/R. Read the axes before interpreting steepness. A straight line with a nonzero intercept also fails the simple proportional law for a passive resistor.

Read the axes first

Problem
A V-versus-I graph through the origin includes (0.20 A, 1.0 V) and (0.60 A, 3.0 V). Find resistance and the slope of the reversed-axis graph.

  1. 1.R = ΔV/ΔI = (3.0 − 1.0)/(0.60 − 0.20) = 5.0 Ω. Each individual V/I also equals 5.0 Ω.
  2. 2.For an I-versus-V graph, the slope is ΔI/ΔV = 0.20 A/V = 0.20 S.
  3. 3.These two slopes are reciprocals because the axes have been interchanged, not because the physical resistor changed.
V–I response: fixed-state line and nonlinear curveI (A)V (V)0108
Ohmic and curved voltage–current responses— Blue is V = 5I with constant R = 5 Ω. Red is the illustrative nonlinear relation V = 5I + 2I³, with coefficients in consistent SI units. Only the blue line has constant V/I.

Geometry changes resistance

Take two identical uniform rods of length L, cross-sectional area A and resistance R. End-to-end, the same current crosses each while their potential drops add; doubling length doubles the total resistance. Side-by-side between the same end faces, the voltage is shared and twice the current can pass, so doubling area halves resistance. Extending these scaling arguments gives R proportional to L/A. The material factor is resistivity ρ, specified at the actual temperature and other physical conditions.

Uniform-sample resistance and local Ohm’s lawLaTeX
L is in m and A in m², so ρ is in Ω m. These sample formulas assume uniform material and cross-section, an approximately axial uniform field and negligible end/contact effects. The vector form assumes isotropy.

Substitute V = IR = IρL/A into E = V/L: the L cancels, leaving E = ρ(I/A) = ρj. Thus the resistance of a sample depends on its shape, while resistivity characterises its local material response. Changing only length does not change ρ. Conductivity σ = 1/ρ is in S/m, whereas the conductance 1/R of an entire sample is in S. These are related but distinct quantities.

Same material and temperatureL, A → R2L, A → 2RL, 2A → R/2
Geometry and resistance at the same material state— Rectangular bars are schematic; end effects and contact resistance are neglected.
Wire resistivity and stretching

Problem
A 15 m wire of area 6.0 × 10⁻⁷ m² has resistance 5.0 Ω. Find ρ. Then predict resistance if it is uniformly stretched to twice its length at constant volume and unchanged ρ.

  1. 1.ρ = RA/L = (5.0)(6.0 × 10⁻⁷)/15 = 2.0 × 10⁻⁷ Ω m. Use a small measuring current so self-heating is negligible.
  2. 2.Constant volume LA means that doubling L halves A. Thus Rnew/Rold = 2/(1/2) = 4 and Rnew = 20 Ω.
  3. 3.This is an ideal geometric prediction. Real stretching can alter microstructure, temperature and hence resistivity, so unchanged ρ must be stated.

How proportionality can fail

There are several different departures. A symmetric curved characteristic can have a voltage-dependent V/I. A diode has a strongly direction-dependent current: equal and opposite voltages need not produce equal and opposite currents. Some devices, including suitable gallium-arsenide structures, have an interval in which current falls while voltage rises. This is negative differential resistance: dI/dV is negative in that interval. It does not automatically mean V/I is negative or that the device creates energy.

VIreverse biasforward biasQualitative shape; no calibrated voltage or current scales
A direction-asymmetric diode characteristic— This schematic shows unequal forward and reverse responses. The negative-V branch has small reverse current over the illustrated interval; reverse breakdown is outside the drawing. It is not an odd-symmetric ohmic line.
Schematic GaAs-type characteristicV / V₀I / I₀010
A nonmonotonic characteristic— V₀ and I₀ are positive scale constants, not measured data. The falling segment has negative differential slope; a horizontal line can intersect more than one voltage.

On the nonmonotonic I–V curve, a given current can correspond to several voltages. This is the precise sense in which the inverse relation V(I) may be nonunique; it is not evidence that a single fixed voltage always has several currents. Device history and circuit constraints can introduce further complications, but they are beyond the simple static illustration. Do not replace these curves by one constant resistance across the entire range.

CharacteristicWhat to checkInterpretation
Straight V–I line through originSame temperature and material stateConstant R over the tested range
Curved but sign-symmetricChanging ratio V/INon-ohmic over that range
Diode-like asymmetryReverse and forward branches separatelyDirection matters; do not infer reverse current by reflection
Falling I–V segmentLocal derivative, not only V/INegative differential resistance can coexist with positive absorbed power

A meaningful measurement

To test a wire, connect an ammeter in series and a voltmeter across the sample. Change one variable at a time, use modest currents, wait for stable readings and monitor temperature. Reverse polarity to test symmetry. Contact and lead resistances can contribute to a small measured resistance; finite voltmeter current and ammeter resistance disturb the ideal circuit. Report a tested range and measurement uncertainty instead of claiming that a few points prove universal linearity. Predict doubling V: I doubles only if the same ohmic state is maintained.

Quick Quiz

Quiz

Quick check

An ohmic resistor at fixed temperature is identified by

Explanation: Ohm’s law requires proportionality, not merely a definable ratio.

Quick check

For a V-versus-I graph, slope has units

Explanation: Voltage divided by current is resistance.

Quick check

Doubling wire radius at fixed L and ρ makes resistance

Explanation: Area grows as radius squared, by a factor of four.

Quick check

Conductivity has SI units

Explanation: Conductivity is inverse resistivity; conductance of a sample is in S.

Quick check

In a positive-V, positive-I region where dI/dV < 0, which follows?

Explanation: A falling local slope does not fix the sign of the positive ratio V/I or VI.

Practice Problems

Practice Problems
  1. A uniform wire has ρ = 1.7 × 10⁻⁸ Ω m, L = 2.0 m and A = 0.50 mm². Find resistance.
  2. A wire is cut into four equal lengths and those lengths are connected in parallel. Find equivalent resistance in terms of original R.
  3. A device carries 1 mA at 1 V and 4 mA at 2 V. Can it be described by one constant resistance?
  4. At fixed current, compare local E in two uniform materials with resistivities ρ and 3ρ and the same area.
  5. Design a low-voltage test to separate self-heating curvature from an intrinsic nonlinear response.

Convert 0.50 mm² to 5.0 × 10⁻⁷ m². Then R = ρL/A = (1.7 × 10⁻⁸)(2.0)/(5.0 × 10⁻⁷) = 0.068 Ω. Confusing square millimetres with millimetres would cause a large error.

Key Takeaways

Key Takeaways

• Ohm’s law is a proportional response at fixed physical conditions. • Defining an operating-point V/I does not prove constant resistance. • For a uniform conductor R = ρL/A. • Resistivity and conductivity describe material response; resistance and conductance describe a sample. • Graph slopes depend on which quantity is on each axis. • Nonlinearity, direction asymmetry and negative differential slope are distinct behaviours. • Measurement conditions and contact effects matter.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…