Current Electricity · Lesson 6 of 10
Cells and Internal Resistance
“Model a cell as an energy source with internal resistance, and derive the different terminal-voltage relations for discharge and charging.”
• Interpret emf as energy supplied per unit charge and distinguish it from a force. • Derive terminal voltage and load current for a discharging cell. • Apply charging signs and check energy conservation. • Use open-circuit and loaded measurements to estimate internal resistance.
What keeps the circuit running?
In the external resistive path, conventional current travels from the cell’s positive terminal toward its negative terminal. To sustain this circulation, non-electrostatic processes inside the source move charge from lower to higher electric potential. Chemical reactions at the electrodes supply the required energy. Electrons travel in the metallic external connections; ions and electrode reactions carry the transport through the electrolyte. It is misleading to imagine one electron simply passing through every part of an ordinary electrolytic cell unchanged.
The electromotive force, written ε, is the non-electrostatic work supplied per unit positive charge in an idealised passage through the source. Despite the historical name, emf is not a force: its unit is the volt, or joule per coulomb. For a relaxed open-circuit cell in the simple model, the terminal potential difference equals ε. Absolute electrode potentials require a reference; their physically relevant differences add to the cell’s emf. An ideal emf by itself does not specify a fixed current—the external circuit and internal resistance determine that.
A useful equivalent circuit
Represent the real cell by an ideal emf in series with a positive internal resistance r. The resistor symbol is a model for internal energy dissipation; r can depend on temperature, state of charge and operating conditions. Treating it as constant is an approximation appropriate to the stated problem. A finite-resistance voltmeter can draw current, so a measured open-circuit value is approximately ε only when meter loading and other transients are negligible.
Discharge: some voltage is lost inside
Let I > 0 denote discharge current leaving the positive terminal, and define V = V_P − V_N. Starting at N and passing inside the source toward P, the ideal emf raises potential by ε, while the internal resistor drops it by Ir along the internal current. The net terminal rise is ε − Ir. In the external resistor the same terminal difference is IR. Equating the two gives the circuit current.
As R tends to infinity, I tends to zero and V tends to ε. As R tends to zero, the simple model gives I_sc = ε/r and V = 0 across the ideal external short. Zero terminal voltage does not mean zero energy conversion: εI_sc is dissipated internally. This short-circuit result is a model limit, not a permissible operating current or an experiment to perform. A real cell’s changing r and chemistry can make the constant-r extrapolation inaccurate.
Problem
A 12 V cell has r = 0.40 Ω and drives R = 5.6 Ω. Find I, V and all power terms.
- 1.I = 12/(5.6 + 0.40) = 2.0 A. Terminal voltage is V = 12 − 2.0 × 0.40 = 11.2 V, also IR = 11.2 V.
- 2.Chemical power supplied in the model is εI = 24 W. External load power is I²R = 22.4 W; internal heating is I²r = 1.6 W.
- 3.Their sum is 24 W. Load efficiency is R/(R+r) = 5.6/6.0 ≈ 93.3%. This does not include additional real chemical or thermal losses beyond the model.
Charging reverses the terminal correction
A rechargeable cell can receive current through its positive terminal from a higher-voltage supply. Define I_c > 0 as that charging-current magnitude. The internal resistor still dissipates I_c²r; it does not acquire a negative resistance. The charger must supply both the emf-related energy increase and internal loss, so the cell terminal voltage is now ε + I_cr. Equivalently, keeping the original signed discharge convention, substitute I = −I_c into V = ε − Ir. Do not change the terminal labels while changing current conventions.
Problem
An 8.0 V storage cell with r = 0.50 Ω is charged from 120 V DC through R_s = 15.5 Ω. Find current, cell terminal voltage and series-resistor heating.
- 1.Net driving voltage is 120 − 8.0 = 112 V. Total series resistance is 16.0 Ω, so I_c = 7.0 A.
- 2.The cell terminal voltage is 8.0 + 7.0 × 0.50 = 11.5 V, not 4.5 V. The limiting resistor drops 7.0 × 15.5 = 108.5 V. The drops sum to 120 V.
- 3.Its heat rate is 7² × 15.5 = 759.5 W; cell internal heating is 24.5 W and ideal chemical storage rate is 56 W. Total input is 840 W. These are idealised problem values, not a practical charging procedure.
Measuring r from voltage sag
For a constant-emf, constant-r cell, a graph of terminal voltage V against signed discharge current I is a straight line with intercept ε and slope −r. Measure a near-open-circuit voltage and the voltage under a known load, keeping state of charge and temperature comparable. Then r = (ε − V)/I. A slope in volts per ampere has units ohms. If the graph curves or changes over time, the simple constant model needs qualification.
Predict increasing external R while keeping ε and r fixed. Current falls, the internal drop Ir shrinks and terminal voltage rises toward ε. The source does not hold current fixed. This is why the brightness of a lamp can depend on the cell’s condition and why equal emfs do not guarantee equal performance under load.
Quick Quiz
Quiz
The unit of emf is
Explanation: Emf is energy per unit charge, not a mechanical force.
A discharging cell’s terminal voltage is
Explanation: The internal resistance reduces terminal voltage when current leaves the positive terminal.
During charging with current magnitude I_c, terminal voltage is
Explanation: The charger supplies both the emf-related energy and internal dissipation.
In the simple open-circuit limit, current and voltage are
Explanation: No load current means no internal Ir drop.
For V plotted against discharge I, slope is
Explanation: The straight-line relation is V = ε − rI.
Practice Problems
- A 12 V cell has r = 0.40 Ω. Calculate the constant-r short-circuit current and explain its status.
- A 10 V cell with r = 3 Ω supplies 0.50 A. Find external resistance and terminal voltage.
- A cell reads 1.50 V with negligible current and 1.20 V at discharge current 0.60 A. Estimate r.
- A 6.0 V rechargeable cell with r = 0.50 Ω receives 2.0 A. Find terminal input power, ideal storage rate and internal heat.
- As the external load resistance of a discharging cell increases, why does terminal voltage rise while load current falls?
With ideal external R = 0, I_sc = ε/r = 12/0.40 = 30 A. The model predicts terminal V = 0 and internal heat I²r = 360 W. This is an extrapolated short-circuit value, not a safe allowed current; real chemistry and resistance can change rapidly.
Key Takeaways
• Emf is non-electrostatic energy supplied per charge, in volts. • A real cell can be modelled by an ideal emf and series internal resistance. • For positive discharge current V = ε − Ir. • For positive charging-current magnitude V = ε + I_cr. • Internal heating is positive for either current direction. • Open-circuit voltage approaches emf in the simple relaxed model. • Short-circuit current is a model limit, not an operating recommendation. • Power balance checks every terminal-voltage calculation.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…