Skip to lesson content

Lesson 1 of 9

Alternating Current · Lesson 1 of 9

Sinusoidal AC and RMS Values

“Read an alternating waveform and derive the effective values that determine resistor heating.”

Learning Objectives

• Distinguish instantaneous, peak, mean and RMS values. • Relate period, frequency and angular frequency. • Derive the RMS value of a sinusoid from heating. • Calculate current, power and energy for an ideal resistor.

A reversing current still transports energy

A heater warms during both directions of an alternating current. Reversal changes the sign of charge transfer through a chosen section; it does not reverse the thermal energy already delivered to the resistor. In a metal the mobile electrons acquire an oscillating drift superposed on random motion. They need not travel from the generator to the appliance in one cycle. The electric field drives their local motion and transfers energy to the material.

Choose a current arrow and a labelled voltage polarity before assigning signs. A positive instantaneous voltage means the first terminal is at higher potential; a negative value means that polarity has reversed. Alternating quantities are periodic and reverse sign. They need not all be sinusoidal, but this chapter develops the sinusoidal, linear-circuit model. A unidirectional varying current is not an alternating current merely because its magnitude changes.

A sinusoidal sourceLaTeX
v is instantaneous voltage in V, Vm its positive peak in V, t time in s, T period in s, f frequency in Hz, and ω angular frequency in rad s⁻¹. The phase origin is chosen at a rising zero crossing.

The argument ωt is an angle in radians. A quarter-cycle takes T/4 and advances phase by π/2; a full cycle advances 2π. At t = 0, T/4, T/2, 3T/4 and T the voltage is respectively 0, +Vm, 0, −Vm and 0. A negative sine value specifies polarity, not a negative amplitude. Frequency counts full cycles; sign reversals occur every half-cycle.

In-phase sinusoidal voltage and current+1−1t/T0.00.250.50.751.0blue: v/Vm; red: i/Im
In-phase sinusoidal voltage and current— Normalized amplitudes; the curves do not equate volts with amperes. One full cycle is shown.

Where a sinusoidal voltage comes from

A simple AC generator rotates a conducting coil mechanically in a uniform magnetic field. Let N be the number of turns, A each turn’s area, B the field magnitude and θ = ωt the angle between the field and the coil’s area normal. The flux linkage is NBA cosθ. Faraday’s law converts its rate of change into an emf. Because the angle changes uniformly, the emf is sinusoidal. The largest flux occurs when the induced emf is zero; the largest emf occurs when flux changes most rapidly.

Rotating-coil sourceLaTeX
B in T, A in m² and ω in rad s⁻¹ give an emf amplitude NBAω in V. This assumes a rigid coil rotating uniformly in a uniform field. The sign depends on the labelled winding orientation.

Slip rings connected to the two coil ends and stationary brushes allow the external polarity to alternate. Mechanical work is required: the induced current creates a magnetic torque opposing the driving motion, consistent with energy conservation. A motor converts electrical input to mechanical output, whereas a generator converts mechanical input to electrical output. A real generator’s terminal voltage also depends on internal impedance and loading; emf and terminal voltage are not always equal.

Predicting a generator amplitude

Problem
A 100-turn coil of area 0.010 m² rotates at 50 cycles per second in a uniform 0.20 T field. Find its ideal emf amplitude and RMS value.

  1. 1.ω = 2πf = 100π rad s⁻¹. Em = NBAω = 100 × 0.010 × 0.20 × 100π = 62.83 V.
  2. 2.For sinusoidal emf, Erms = 62.83/√2 = 44.43 V. At maximum flux the instantaneous emf is zero, not 62.83 V.
  3. 3.Doubling rotation speed doubles emf amplitude and frequency at fixed N, B and A. The mechanical energy source must provide the output electrical energy.

The resistor responds instant by instant

For an ideal ohmic resistor at constant temperature, v = iR at every instant. Substituting the sinusoidal voltage gives i = (Vm/R) sin(ωt), so Im = Vm/R. Current and voltage reach corresponding zeros and peaks together: they are in phase. R is assumed independent of frequency and temperature here. A real lamp changes resistance as its filament heats, so calculations from its operating rating describe its hot working resistance.

Instantaneous heating and its meanLaTeX
p is instantaneous absorbed power and P its cycle average, both in W. p is nonnegative for a passive resistor, including when voltage and current are both negative.

Deriving a useful effective current

The signed average current over a complete sine cycle is zero because equal positive and negative areas cancel. Heating depends on the square, which cannot cancel this way. Define the root mean square by squaring the instantaneous current, averaging over a period, then taking the positive square root. The order of those operations matters: the RMS is not the square of the mean or the mean magnitude.

RMS definition and sinusoidal resultLaTeX
Use sin²θ = (1 − cos 2θ)/2. The cosine integral contributes [sin(2ωt)/(2ω)] from 0 to T, which is zero since ωT = 2π.
Effective values for a pure sine waveLaTeX
An RMS current gives the same average heating as the numerically equal steady DC current in the same resistor. √2 conversion requires a pure sinusoid; the integral definition is more general.

Dimensions provide a check: A²Ω = W and W s = J. RMS voltage is not a constant voltage actually present at every instant. A 220 V sinusoidal rating corresponds to a peak near 311 V. Unless explicitly stated otherwise, numerical AC supply values in these lessons are RMS. A full-cycle signed average is different from a half-cycle mean or a rectified mean; those cannot replace RMS in the heating equation.

A lamp at its operating rating

Problem
A lamp consumes 100 W from a 220 V sinusoidal supply. Find its hot resistance, RMS current and peak voltage.

  1. 1.At the stated operating condition, model the filament as resistive. R = V²/P = 220²/100 = 484 Ω.
  2. 2.I = P/V = 100/220 = 0.455 A. Vm = √2 × 220 = 311 V.
  3. 3.In 60 s it receives E = Pt = 6000 J. The net charge transfer over whole cycles is zero, but its energy absorption is positive.
Reading a waveform

Problem
A source is v = 170 sin(100πt) V across 85 Ω. Find frequency, period, current at 5 ms and mean power.

  1. 1.Vm = 170 V and ω = 100π rad s⁻¹; f = 50 Hz and T = 0.020 s.
  2. 2.At 0.005 s, phase is π/2, so v = 170 V and i = 2.00 A, its peak.
  3. 3.Irms = 2/√2 A. P = (2²/2) × 85 = 170 W. At 10 ms the instantaneous power is zero, although the cycle mean remains 170 W.

Quick Quiz

Quiz

Quick check

A sine current has zero signed mean. Its resistor heating is

Explanation: Squaring current removes the sign cancellation.

Quick check

A 50 Hz sine voltage has period

Explanation: T = 1/50 s = 20 ms.

Quick check

For a sinusoidal 10 A peak current, RMS current is

Explanation: Divide the peak by √2.

Quick check

For an ideal resistor, voltage and current are

Explanation: The instantaneous relation i = v/R multiplies by a positive constant.

Quick check

Doubling RMS voltage across fixed R changes mean power by

Explanation: P = V²/R at fixed R.

Practice Problems

Practice Problems
  1. A 100 Ω resistor uses a 220 V, 50 Hz sine supply. Find RMS current, mean power and energy in one cycle.
  2. A sine source has peak voltage 300 V; another sine current has RMS value 10 A. Convert each to the other amplitude measure.
  3. A sine voltage has period 4 ms. Find f, ω and the time to its first positive peak from a rising zero.
  4. Explain why an AC ammeter reading of 2 A does not mean 2 C crosses in one direction every second.
  5. A symmetric square current is +3 A for half a cycle and −3 A for half. Find its mean and RMS and compare its heating with a 3 A peak sinusoid in the same R.

I = 220/100 = 2.20 A. P = V²/R = 484 W. T = 0.020 s, so energy per cycle is PT = 9.68 J. Zero signed mean current does not make this energy zero.

Key Takeaways

Key Takeaways

• Sinusoidal AC reverses polarity and current direction periodically. • ω = 2πf and T = 1/f; angular frequency uses rad s⁻¹. • A resistor has in-phase voltage and current. • The signed cycle mean can vanish while heating remains positive. • RMS is the square root of the mean square. • For a sine wave, RMS equals peak/√2. • Mean resistor power is I²R when I is RMS.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…