Alternating Current · Lesson 6 of 9
Resonance and Energy Exchange
“Connect resonant current, free LC oscillations and frequency selectivity through energy and reactance.”
• Derive the resonance frequency of a series LCR circuit. • Explain cancellation of reactive voltages without loss of stored energy. • Derive free LC oscillations from the loop equation. • Relate resistance and quality factor to the shape of a resonance curve.
A circuit can respond most strongly at one frequency
A driven swing gains a large amplitude when repeated pushes occur at an appropriate rhythm. An electrical circuit containing L and C likewise has a characteristic energy-exchange timescale. The capacitor stores electric-field energy and the inductor stores magnetic-field energy. The source replenishes energy dissipated by resistance. In a series circuit at fixed voltage amplitude, current is greatest when the net reactive opposition vanishes.
At resonance, the signed net reactance is zero. Z is then its minimum R, so I = V/R is maximum for a fixed RMS source voltage and fixed positive R. The source and current are in phase. The two component voltages need not be small; they cancel because they have equal magnitude and opposite phase. This condition maximises current, not every possible response variable in every resonant system.
Free LC oscillations explain the natural timescale
Disconnect the source and resistance in an idealised charged-capacitor/inductor loop. Let q denote signed charge on the plate into which the chosen reference current would flow, so i = dq/dt. The passive drops around the source-free loop satisfy L di/dt + q/C = 0. Therefore the charge obeys a restoring equation: its second derivative is proportional to its negative value. This has the same mathematical form as simple harmonic motion.
Start with all energy in the charged capacitor. The potential difference drives a current; as |q| falls, |i| and magnetic energy grow. At a quarter period q = 0 and |i| is maximum. The inductor maintains current while it decreases, charging the capacitor with the opposite polarity. At half a period the capacitor has −qm and current is zero. The process reverses and repeats. Inductance does not create energy; it allows magnetic storage to sustain the transfer.
Resistance controls the resonance peak
At frequencies below resonance the capacitor dominates and current leads. At high frequencies the inductor dominates and current lags. On either side, the magnitude of net reactance raises impedance and lowers current. A smaller fixed R raises the resonant peak and makes the normalized current response more selective in frequency. Do not assume a symmetric current curve on a linear frequency axis; the exact equation determines its shape.
For the same model, the frequencies at which mean resistor power falls to half its resonant value satisfy |XL − XC| = R. Their angular-frequency separation is Δω = R/L, so Q = ω0/Δω. This gives a quantitative meaning to selectivity; it is an extension of the source’s quality-factor entry rather than a separate circuit model. It assumes frequency-independent R, L, C and fixed source voltage.
Problem
R = 40 Ω, L = 5.0 H, C = 80 μF and source RMS voltage 230 V. Find resonant frequency and component voltages.
- 1.LC = 0.000400 s², so ω0 = 50.0 rad s⁻¹ and f0 = 7.96 Hz. Z0 = 40 Ω and I0 = 5.75 A RMS; Im = 8.13 A.
- 2.XL = XC = 250 Ω. VR = 230 V, VL = VC = 1437.5 V RMS, and their sum as opposite phasors is zero.
- 3.Q = 250/40 = 6.25 explains the magnification. The result flags component voltage ratings as significant, even with a 230 V source.
Problem
C = 30 μF and L = 27 mH form an ideal free oscillator. Find ω0 and compare a quadrupled capacitance.
- 1.LC = (30 × 10⁻⁶)(27 × 10⁻³) = 8.10 × 10⁻⁷ s². ω0 = 1111 rad s⁻¹ and f0 ≈ 177 Hz.
- 2.Quadrupling C multiplies LC by four and its square root by two, so ω0 and f0 halve.
- 3.Frequency does not depend on initial charge in this linear ideal model; charge determines energy and current amplitude instead.
Tuning and limits of the model
A radio tuning stage can adjust capacitance so its resonant response favours a selected signal frequency. Real radio circuits include coupling, loading and often parallel resonant arrangements; the series model teaches selectivity without describing every receiver. Some metal detectors sense a change in coil inductance or losses caused by nearby metal, which changes a tuned response. Other designs use pulse induction, so resonance is not a universal description of every detector.
A simple ideal series RL or RC circuit cannot cancel both kinds of reactance because only one is present; it has no finite-frequency series resonance of this kind. This does not deny resonance in distributed circuits or real components with parasitic L and C. Similarly, the formally infinite current at R = 0 and exact drive resonance signals failure of a bounded sinusoidal steady state; energy can accumulate instead of settling.
Testing a resonance curve
A test of the model uses a low-voltage sinusoidal signal source, known series R, L and C, and a suitable AC current measurement or oscilloscope with a small sensing resistor. Hold source RMS voltage at the circuit terminals constant while varying frequency. Record frequency and current after transients settle; also compare the source and resistor-voltage timing. The model predicts a current maximum and zero source-current phase at XL = XC. Repeating with a larger R should lower the peak and broaden the normalized response. These are predicted observations, not fabricated measurements.
Measurement limitations matter: a signal source has internal resistance, a coil has winding resistance and core losses, and meters have limited frequency response. Include resistive contributions in total R and check the actual terminal voltage during the sweep. An observed peak shifted from the simple prediction can indicate nonideal or frequency-dependent components rather than failure of charge conservation. The same approach tests an iron core’s effect on an RL impedance while holding frequency and terminal voltage fixed.
Quick Quiz
Quiz
At ideal series resonance,
Explanation: Equal opposite reactive voltage contributions cancel.
For fixed L and C, reducing R makes the resonant current
Explanation: At resonance I = V/R for a fixed voltage and positive R.
In free ideal LC motion, maximum current occurs when
Explanation: Energy is then entirely magnetic.
Quadrupling L at fixed C makes f0
Explanation: f0 varies inversely as √L.
A large Q at resonance can mean
Explanation: VL/V = VC/V = Q for the ideal series model.
Practice Problems
- A 20 Ω, 1.5 H, 35 μF series circuit uses 200 V RMS at resonance. Find frequency, current and mean power.
- L = 1.00 mH, C = 1.00 nF and Vm = 100 V. Compare resonant peak current for R = 100 Ω and 200 Ω.
- An ideal free LC loop has C = 10 μF, L = 0.10 H and initial capacitor voltage 100 V. Find total energy and peak current.
- A circuit has Q = 8 at resonance and a 12 V RMS source. Find each reactive voltage and their series sum.
- A tunable circuit must double its resonant frequency while L stays fixed. How must C change, and why can RL alone not achieve the same cancellation?
ω0 = 1/√[(1.5)(35 × 10⁻⁶)] = 138.0 rad s⁻¹; f0 = 21.97 Hz. I = 200/20 = 10 A. Mean resistor power is I²R = 2000 W. The nonzero L and C voltages cancel as phasors.
Key Takeaways
• Resonance is a maximum-current response at fixed source voltage in the series model. • ω0 = 1/√(LC), whereas f0 = ω0/(2π). • At resonance Z = R and voltage is in phase with current. • Equal inductive and capacitive voltages cancel but can each be large. • Free LC oscillations transfer energy between electric and magnetic fields. • Resistance dissipates energy and broadens the normalized response. • Q measures selectivity and internal voltage magnification in the ideal series model.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…