Skip to lesson content

Lesson 3 of 9

Alternating Current · Lesson 3 of 9

Inductors in AC Circuits

“Derive the lagging current of an ideal inductor and track magnetic energy through an AC cycle.”

Learning Objectives

• Derive current from the inductor voltage law. • Explain the 90° current lag using slopes and phase. • Calculate inductive reactance and current. • Distinguish energy storage from dissipation and state the steady-state assumption.

A coil opposes changes in current

A coil carrying current creates a magnetic field. Changing that current changes magnetic flux, inducing an emf that opposes the change. This is self-induction. The opposition is to changing current, not to current itself. A large steady current can persist in a low-resistance coil with little voltage, whereas a rapidly changing current requires substantial voltage. Real windings have resistance; first isolate the inductive behaviour by treating it as negligible.

Terminal voltage and induced emfLaTeX
L is inductance in H. vL is the passive terminal voltage drop measured in the direction of positive current; the internal induced emf has the opposite sign in a loop equation. H = V s A⁻¹.

For a source v = Vm sin(ωt) across the ideal coil, Kirchhoff’s rule is v − L di/dt = 0. Thus di/dt = (Vm/L) sin(ωt). This determines the slope of current. When voltage is zero the current has zero slope; when voltage is a positive maximum the current is increasing most rapidly. Large voltage does not mean current is then at its maximum.

Integrate the voltage lawLaTeX
The antiderivative of sin(ωt) is −cos(ωt)/ω. K is a constant current fixed by the initial condition, not by voltage symmetry alone.

In a mathematically ideal zero-resistance inductor, K can persist indefinitely. A symmetric source does not force K to zero. To describe the purely sinusoidal response we choose the zero-offset periodic solution; in a real coil resistance causes the initial transient to decay, leaving its driven steady state. The pure-inductor result is the limiting sinusoidal model, not a general switching solution. For example, imposing i(0) = 0 with this voltage phase would require K = Vm/(ωL).

Sinusoidal inductive responseLaTeX
For the zero-offset sinusoidal solution, current lags voltage by 90°. XL is inductive reactance in Ω. RMS values satisfy I = V/XL as well.
Inductor: current lags voltage+1−1t/T0.00.250.50.751.0blue: v/Vm; red: i/Im
Inductor: current lags voltage— Normalized amplitudes; the curves do not equate volts with amperes. One full cycle is shown.

Starting at a rising voltage zero, the zero-offset current is at its negative peak. During the next quarter-cycle the positive voltage increases the current to zero. It reaches a positive peak at half a cycle, when voltage returns to zero. This time sequence explains the quarter-cycle delay without treating L as an ordinary resistor. At fixed RMS voltage and L, doubling frequency doubles XL and halves current. At fixed frequency, doubling L has the same effect.

Energy goes into the field and comes back

Multiplying the passive voltage law by i gives p = Li di/dt. Because the derivative of i² is 2i di/dt, this equals d(½Li²)/dt. The magnetic field stores energy as current magnitude increases and returns it as current magnitude decreases. Current can be negative while its magnitude is increasing; energy storage depends on i², not on the sign of i.

Stored magnetic energy and powerLaTeX
UL is in J. Positive pL means energy enters the field; negative pL means it returns to the rest of the circuit. The power result uses the pure sinusoidal zero-offset response.
Inductive instantaneous power+1−1t/T0.00.250.50.751.0p/(Vm Im): positive means energy enters the element
Inductive instantaneous power— Normalized amplitudes; the curves do not equate volts with amperes. One full cycle is shown.

Zero average power means zero net energy absorbed over a complete cycle; it does not mean zero current or zero energy at every instant. Reactance has the same unit as resistance because it relates voltage and current amplitudes, but it does not measure irreversible heating. In a real coil the winding resistance dissipates I²R and core effects can add losses. Neither an ideal zero-power result nor the coil’s reactance is a claim that a practical coil stays cold.

A purely inductive load

Problem
An ideal 25.0 mH inductor is connected to 220 V RMS at 50 Hz. Find reactance, current and peak stored energy.

  1. 1.Convert L = 0.0250 H. XL = 2π × 50 × 0.0250 = 7.85 Ω. I = 220/7.85 = 28.0 A.
  2. 2.Im = √2I = 39.6 A. Umax = ½ × 0.0250 × 39.6² ≈ 19.6 J.
  3. 3.Despite this sizeable exchange, average power is zero in the ideal model. The large current makes omitted winding resistance consequential in a real device.
Inserting an iron core

Problem
A lamp and coil are in series across a fixed-frequency AC source. Predict the change in glow when a suitable iron core raises L, assuming other losses stay fixed.

  1. 1.For series RL, the coil’s induced voltage is a quarter-cycle from the resistor voltage. The total opposition has magnitude √(R² + (ωL)²).
  2. 2.Increasing L increases that magnitude, reducing RMS current and lamp heating I²R. The lamp becomes dimmer.
  3. 3.The assumption of unchanged losses isolates inductance. Real iron can also introduce hysteresis and eddy-current heating; the simple prediction is not a complete material model.

Quick Quiz

Quiz

Quick check

For a pure inductor, current

Explanation: Integration shifts the sinusoidal current a quarter-cycle behind voltage.

Quick check

At a current extremum in an ideal coil, vL is

Explanation: At an extremum di/dt = 0.

Quick check

At fixed V and L, doubling f makes RMS current

Explanation: XL = 2πfL doubles, so V/XL halves.

Quick check

Negative passive instantaneous power means

Explanation: The magnetic field releases previously stored energy.

Quick check

The constant K in the ideal inductor solution is fixed by

Explanation: No resistance exists to remove an arbitrary constant current component.

Practice Problems

Practice Problems
  1. A 44 mH ideal coil uses 220 V RMS at 50 Hz. Find its RMS current and mean power.
  2. For L = 0.10 H and i = 3 sin(200t) A, derive vL(t).
  3. An ideal 0.20 H coil carries 4 A instantaneously. Find its energy and the energy at −4 A.
  4. A pure inductor sees v = Vm sin(ωt) and starts with i(0) = 0. Is the zero-offset expression its complete current?
  5. A coil and lamp draw a smaller current after L doubles. Explain why increased reactance is not itself extra average heating.

XL = 2π(50)(0.044) = 13.82 Ω. I = 220/13.82 = 15.9 A. Average power is zero because ideal field storage is returned each cycle; the result excludes winding and core losses.

Key Takeaways

Key Takeaways

• Inductance opposes current change through self-induced emf. • The passive voltage drop is L di/dt. • Pure sinusoidal current lags inductive voltage by 90°. • XL = ωL increases with frequency and inductance. • Initial conditions can produce a persistent offset in a perfectly ideal coil. • Magnetic energy is ½Li². • Ideal inductance exchanges energy but has zero average dissipation.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…