Skip to lesson content

Lesson 5 of 8

Wave Optics · Lesson 5 of 8

Fringe Calculations, Colour and Changing Conditions

“Solve interference inverse problems, predict scaling and analyse coincident fringes without inventing missing geometry.”

Learning Objectives

• Rearrange fringe relations and convert units reliably. • Predict changes with wavelength, slit separation, screen distance and medium. • Find coincident bright orders for two wavelengths. • Identify when an interference distance is underdetermined.

Use an organised path from observation to wavelength

A measured screen distance is not automatically a fringe spacing. It may be a distance from the centre to a numbered order, a span over several adjacent fringes, or a bright-to-dark separation. Begin by marking the central order and labelling what has actually been measured. Then select the bright or dark position equation and only afterward substitute values. This avoids errors that arithmetic alone cannot expose.

Useful inverse relationsLaTeX
Use one consistent length unit. Convert nm = 10⁻⁹ m, μm = 10⁻⁶ m, mm = 10⁻³ m and cm = 10⁻² m before substitution.

Check the result against visible wavelengths when the experiment uses visible light. A result of 600 mm for red-yellow light is not a subtle new effect; it almost certainly signals a missing power of ten. Physical plausibility and dimensions are complementary checks. The same formula applies to other wave frequencies when the apparatus and propagation model are appropriate, so the visible range is a contextual check, not a universal numerical rule.

Measure several intervals

Problem
The distance between the first and sixth bright fringes on the positive side is 10.0 mm. Slits are 0.40 mm apart and D = 1.6 m. Find wavelength.

  1. 1.There are five intervals between orders 1 and 6, so β = 10.0/5 = 2.0 mm.
  2. 2.λ = βd/D = (2.0 × 10⁻³)(0.40 × 10⁻³)/1.6 = 5.0 × 10⁻⁷ m = 500 nm.
  3. 3.Dividing by six would count bright peaks rather than the intervals between their positions.

Predict changes while holding the other variables fixed

ChangeNew spacing relative to old βPhysical reason
Double screen distance D2βA fixed angular separation maps to twice the transverse distance
Double slit separation dβ/2Path difference varies faster with screen position
Replace λ by a longer wavelength λ′(λ′/λ)βMore path difference is needed per phase cycle
Fill the whole arrangement with uniform index nβ/nWavelength falls to λ₀/n at unchanged source frequency

The medium rule assumes the entire relevant propagation region has one uniform index and the same geometry. It is not the rule for inserting a slab into only one path; such an arrangement introduces an unequal optical delay and can shift the pattern. We do not need a separate slab-shift formula to recognise that changing all paths uniformly differs from changing one path alone.

Fringes in a uniform liquid

Problem
A pattern has β_air = 3.0 mm. The unchanged arrangement is wholly immersed in a transparent liquid with n = 1.50. What is the new spacing?

  1. 1.Frequency remains fixed and material wavelength becomes λ₀/n. Thus β_liquid = β_air/n = 2.0 mm.
  2. 2.The centre remains equal-path under the stated symmetric illumination. The beams do not gain photon energy merely because their material wavelength shortens.

Two colours make two superposed fringe patterns

A beam containing two distinct wavelengths produces an interference distribution for each colour. Their ordinary time-averaged intensities add; the widely different optical frequencies do not give one stationary cross-colour fringe term on an ordinary detector. Each colour nevertheless interferes with its own two coherent slit contributions. A point can therefore be bright for one colour and not the other.

The spacing of a colour is proportional to its wavelength in the same medium. Red fringes are farther apart than shorter-wavelength fringes. All colours have a bright equal-path central fringe under in-phase illumination. With broad white light the centre can appear white, nearby fringes are coloured, and distant overlapping colour patterns lose simple contrast. A two-colour calculation is more precise: match integer bright orders for the two wavelengths.

Coincident bright ordersLaTeX
m and p are integers for the same side of the centre. Exclude m = p = 0 when asked for the least nonzero coincidence. Wavelengths must refer to the same propagation medium.
Bright-order positions for two wavelengths650 nm520 nm012340123454 × 650 nm = 5 × 520 nmOrder zero also coincides; first nonzero coincidence is marked.
The least nonzero coincidence— Horizontal scale is proportional to order times wavelength for a fixed D/d. Marks show bright orders, not a continuous intensity curve.
A complete two-colour numerical example

Problem
An independent apparatus has D = 1.2 m and d = 0.30 mm. Its two wavelengths are 650 nm and 520 nm. Find the third 650 nm bright and the first nonzero coincidence.

  1. 1.D/d = 4000. The third 650 nm bright lies at 3 × 650 × 10⁻⁹ × 4000 = 7.8 × 10⁻³ m = 7.8 mm.
  2. 2.Reduce m650 = p520 to 5m = 4p. The smallest positive solution is m = 4 and p = 5. The common path difference is 2600 nm, giving y = 2600 × 10⁻⁹ × 4000 = 10.4 mm.
  3. 3.This numerical distance depends on the apparatus values explicitly supplied here; wavelengths alone would determine orders but not a screen distance.

What can be determined when geometry is missing?

Suppose only the two wavelengths 650 nm and 520 nm are supplied. Their third 650 nm bright has y₃ = 3(650 nm)D/d. The first nonzero coincidence still has orders 4 and 5 because this is a wavelength ratio. Its position is (2600 nm)D/d. Without D/d, neither distance is a unique number in millimetres. A symbolic result is the complete physical answer to incomplete geometry, rather than a failure to choose a formula.

Two-colour results when D/d is unspecifiedLaTeX
The ratio D/d is dimensionless. These are lengths, not bare numerical distances. They require the standard near-axis coherent-source assumptions.

Intensity calculations require phase, not just position labels

If a question gives intensity K at an integer-wavelength path difference for equal coherent contributions, K is the maximum 4I₀. For another path difference, calculate the phase 2πΔ/λ and evaluate cos² of half that phase. Calling a point “one third of a wavelength farther” does not mean one third of the intensity. Nor does a zero equal-beam minimum remain zero if a slit amplitude is strongly reduced.

A fractional path difference

Problem
A bright maximum has intensity K. Find intensity where initially in-phase equal beams have Δ = λ/6.

  1. 1.I/K = cos²(πΔ/λ) = cos²(π/6) = 3/4. Thus I = 3K/4.
  2. 2.This differs from Δ = λ/3, which gives K/4. Stating both path and phase prevents a factor-of-two error in the angle.

Quick Quiz

Quiz

Quick check

Orders 2 and 7 are 15 mm apart. The fringe spacing is

Explanation: The order difference is five, so there are five spacings.

Quick check

Uniform immersion in index n at fixed geometry changes β to

Explanation: The common wavelength becomes λ₀/n while f stays fixed.

Quick check

For 650 nm and 520 nm, the first positive coincident bright orders are

Explanation: 4 × 650 = 5 × 520 = 2600 nm.

Quick check

Wavelengths alone specify which of these without geometry?

Explanation: β₁/β₂ = λ₁/λ₂; an absolute spacing still requires D/d.

Quick check

A maximum intensity K becomes what at Δ = λ/3 for equal in-phase beams?

Explanation: I/K = cos²(π/3) = 1/4.

Practice Problems

Practice Problems
  1. Orders 1 and 5 are separated by 8.0 mm. With d = 0.50 mm and D = 2.0 m, find wavelength.
  2. A 600 nm pattern is replaced by 450 nm light at the same D and d. If the original spacing was 2.4 mm, find the new spacing and the position of its second positive dark.
  3. For wavelengths 650 nm and 520 nm with no D or d supplied, give the third 650 nm bright and first nonzero coincidence position.
  4. Two colours 600 nm and 450 nm illuminate the same slits. Find the least positive coincident bright orders and the spacing ratio.
  5. An ideal pattern is immersed uniformly in liquid of index 4/3. Explain the changes to spacing, central position and frequency.

Four intervals give β = 2.0 mm. Then λ = βd/D = (2.0 × 10⁻³)(0.50 × 10⁻³)/2.0 = 5.0 × 10⁻⁷ m = 500 nm. The result is visible and the length dimensions are consistent.

Key Takeaways

Key Takeaways

• Read whether a measured distance is an order position or a span of intervals. • Use consistent SI length units before numerical substitution. • Fringe spacing scales as λD/d. • Uniform immersion reduces wavelength and spacing at unchanged frequency. • Distinct colours form superposed patterns with different spacings. • Coincident bright fringes require integer wavelength multiples to match. • Missing D/d prevents a unique screen distance even when the matching orders are known.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…