Skip to lesson content

Lesson 8 of 8

Magnetism and Matter · Lesson 8 of 8

Chapter Summary and Practice

“Connect dipole fields, torque, flux and material response through a chapter-wide reference and mixed reasoning problems.”

Learning Objectives

• Choose the appropriate dipole, flux or material-response model. • Connect field geometry with torque, energy and equilibrium. • Check units, signs and assumptions across magnetic calculations. • Solve mixed problems involving coil moments and magnetic materials.

One connected picture of magnetism

A current loop produces a magnetic dipole field. Atomic orbital and spin moments allow neutral matter to exhibit related magnetic behaviour. A finite solenoid and a bar magnet consequently resemble each other externally, especially far from their sources. Magnetic moment m describes the strength and orientation of a compact source. Magnetisation M instead describes the net moment per unit volume of material. Confusing those two quantities loses the connection between microscopic addition and macroscopic fields.

Start a problem by deciding what is being described. To find the far field generated by a compact source, use its moment and observation position. To find the torque on a dipole, use the external field at that dipole. To evaluate flux, identify the oriented surface. To find the response of a material, specify its constitutive relation and geometry. Several equations may be correct separately but cannot be interchanged without these distinctions.

Source geometry and field direction

A magnet’s moment points internally from S to N. The far axial field is parallel to that moment on both axial sides, while the equatorial field is opposite. At the same large distance their magnitudes have ratio 2:1. Both decrease as r⁻³ at fixed angular position. The dipole model requires distances much greater than source dimensions; its divergence as r approaches zero is outside its valid range. Background and other fields add vectorially.

Field lines encode direction through tangents and relative strength through a consistent drawing density. Outside a bar they point N to S; inside they return S to N. They are not paths of magnetic force on moving charges, because q(v × B) is perpendicular to B. A straight wire or ideal toroid can have a magnetic field without bar-like pole ends. Magnetic Gauss’s law concerns flux through a closed surface, whereas Ampère’s law concerns circulation around a curve.

SNEquatorial: B opposite mm directionAxialAxial
Axial and equatorial field directions— Schematic positions; use dipole formulas only far from the magnet.

Rotation connects torque with energy

For a fixed dipole in a uniform external field, the net force is zero and torque is m × B. With B along +x and positive angle measured counterclockwise, the signed turning torque is −mB sinθ. The magnitude mB sinθ is largest at 90° and zero at parallel and antiparallel orientations. Those two zeros have different stability: parallel minimises U = −mB cosθ, while antiparallel maximises it.

The energy expression follows from dU = −τz dθ, not from treating torque magnitude as always positive work. Integrating gives U = −mB cosθ after choosing zero at 90°. Slow external rotation raises energy by mB(cosθi − cosθf). The field does the opposite work. Without damping a displaced free dipole may oscillate rather than simply settle. For a second magnet in the first magnet’s field, use the local field and state whether the centres are held fixed before discussing equilibrium.

Flux describes passage through a surface

For a flat surface in uniform B, flux is BA cosα with α measured from the surface normal. Flux is a signed scalar, and changing an open surface’s chosen normal changes its sign. For a closed surface all normals point outward; entering contributions are negative and leaving ones positive. Their sum is zero for ordinary magnetic fields, including surfaces surrounding a magnet or only one visible pole region. Return flux through the material must be counted. Zero net flux cannot be used to conclude zero field.

Matter changes the relation between H and B

Magnetisation is M = mnet/V. Define H = B/μ₀ − M, giving B = μ₀(H + M). For a long uniformly filled solenoid away from its ends, H = nI. For a linear isotropic material M = χH, giving μr = 1 + χ and B = μ₀μrH. Finite specimen shapes can alter internal H through demagnetising effects. Nonlinear ferromagnets and anisotropic materials need more than a single scalar constant χ.

Material classMicroscopic origin of net responseχ and responseTemperature and persistence
Ordinary diamagnetField-induced opposing electronic contributionSmall negative; towards weaker nonuniform fieldOften weak temperature dependence; no ordinary retained induced moment
Weak paramagnetPartial bias of existing moments against thermal disorderSmall positive; towards stronger nonuniform fieldSuitable local-moment systems follow χ ≈ C/T in weak fields; no ordinary retained bulk alignment
Ferromagnet below ordering temperatureCollective ordering in domains; wall motion and rotationStrong, generally nonlinear and history dependentHard materials retain magnetisation; spontaneous order is lost above Curie temperature
Ideal superconducting Meissner bulkFlux-expelling superconducting stateM = −H, χ = −1 in the ideal modelRequires appropriate material, temperature and field conditions

Formula reference with meaning and conditions

RelationshipSymbols and SI unitsMeaning and condition
m = NIAm: A m²; I: A; A: m²; N: turn countAligned planar coil turns; direction from right-hand normal
Bax = (μ₀/4π)(2m/r³)B: T; m: A m²; r: mFar axial magnitude, parallel to m; vacuum or approximately air
Beq = (μ₀/4π)(m/r³)Same units as axial relationFar equatorial magnitude, opposite to m
τ = mB sinθτ: N m; B: T; θ: angleFixed small dipole; uniform external field over source
U = −mB cosθU: JFixed m and imposed B; zero chosen at 90°
Wext = mB(cosθi − cosθf)W: JSlow rotation, negligible kinetic change and loss
ΦB = BA cosαΦB: Wb; A: m²Uniform field, flat area; α is angle to normal
Closed-surface B flux = 0Flux: WbAll outward signed surface contributions; ordinary magnetic sources
M = mnet/VM: A/m; V: m³Uniform sample average or local macroscopic moment density
B = μ₀(H + M)H: A/m; μ₀: T m/AMacroscopic definition of H
H = nIn: m⁻¹; I: ALong uniformly filled solenoid, negligible ends
M = χH; μr = 1 + χχ, μr dimensionlessLinear isotropic constitutive response in stated range
B = μH; μ = μ₀μrμ: T m/A = N/A²Same linear-material model
Ieq = μrI; IM = (μr − 1)ICurrents: AEquivalent empty-solenoid current for the same B at the specified operating point
χ = C/TC: K; T: KLimited weak-field local-moment paramagnetic model
Vector relations worth keeping togetherLaTeX
Torque is a vector from a cross product. Energy and flux are scalars from dot products. B in the torque and energy relations is external to the dipole.

A units check can expose a wrong model

Magnetic moment has dimensions current × length² and units A m², equivalently J/T. It does not have dimensions A/length². Magnetisation and H both have units A/m. Magnetic flux has units weber (Wb), not watt (W). Since B is T, multiplying by moment gives J, while multiplying by area gives Wb. Use μ₀ ≈ 4π × 10⁻⁷ T m/A for the numerical precision here; this is a convenient approximation rather than an exact modern SI constant.

One coil, two distinct questions

Problem
A 500-turn coil has area 4.0 × 10⁻⁴ m² and current 1.0 A. Find its far axial field at 0.20 m and its torque in a separate uniform field 0.10 T at 30°.

  1. 1.First find the source moment: m = NIA = 0.20 A m². Assume 0.20 m is much greater than the coil dimensions.
  2. 2.Its generated axial field is 10⁻⁷ × 2 × 0.20/0.20³ = 5.0 × 10⁻⁶ T along the coil moment.
  3. 3.The torque in the imposed field is 0.20 × 0.10 × sin30° = 0.010 N m. Use the imposed 0.10 T, not the coil’s own 5 μT far field.
  4. 4.A field calculation and a torque calculation can share the same moment while referring to different fields and geometries.
A small response is still measurable in principle

Problem
A linear material with χ = −5.0 × 10⁻⁴ fills a long solenoid with n = 2000 m⁻¹ and I = 0.50 A. Find H, M and B.

  1. 1.H = nI = 1000 A/m. M = χH = −0.50 A/m, opposing H.
  2. 2.μr = 0.9995, so B = μ₀ × 999.5 A/m = 1.256009 × 10⁻³ T.
  3. 3.The empty value is 1.256637 × 10⁻³ T, larger by 6.2832 × 10⁻⁷ T. A negative M need not make B negative.
  4. 4.The calculation assumes uniform filling, negligible end fields and linear isotropic behaviour at the specified conditions.

A final reasoning checklist

Draw the relevant source, position, external field or surface normal before substituting. Convert centimetres squared and cubed carefully. State where the field is evaluated. Separate a positive magnitude from a signed component. Check whether a claimed force needs a gradient, whether a material law is linear, and whether distance or temperature lies within its range. Finally interpret the answer: its direction, relative size and response to a changed condition should agree with the physical model.

Quick Quiz

Quiz

Quick check

A magnet’s own far field should be used in m × B to calculate

Use the field as external to the dipole being acted on. A second dipole can experience torque from the first.

Quick check

Two equally sized linear samples at the same H have χ = ±10⁻⁵. Which statement is correct?

M = χH makes their equal-magnitude magnetisations point in opposite directions.

Quick check

A field is nonzero everywhere inside a cube. Its net closed-surface flux

Entering and leaving flux balance, as in the uniform-field cube example.

Quick check

A coil’s current reverses at fixed geometry and magnitude. Its moment

m = NIA times the right-hand normal changes sign with current.

Quick check

Which pair correctly compares stable alignment with zero torque?

Both sin0° and sin180° vanish, but energy is a minimum only at parallel alignment.

Practice Problems

Practice Problems
  1. A magnet at 30° in a 0.25 T uniform field has torque 0.045 N m. Find its moment and maximum torque in that field.
  2. For m = 0.32 A m² and B = 0.15 T, find stable/unstable orientations, their energies and slow work between them.
  3. An 800-turn solenoid has area 2.5 × 10⁻⁴ m² and current 3.0 A. Find its moment and torque in a 0.25 T uniform field at 30°.
  4. A 1.5 A m² magnet starts parallel to a 0.22 T field. Find external work to reach 90° and 180°, and torque at each endpoint.
  5. A 2000-turn coil of area 1.6 × 10⁻⁴ m² carries 4.0 A. Calculate force and torque in a 0.075 T uniform field at 30°.
  6. A 0.48 A m² magnet points +x. Find its axial and equatorial fields 0.10 m away and their values at 0.20 m. Assume both distances are far from the source.
  7. A closed surface has net inward contribution −7.0 μWb over one region. Find the net contribution over the rest, and say whether B inside must be zero.
  8. A long solenoid has 1000 turns/m, 2.0 A current and a specified effective μr = 400. Find H, M, B and the equivalent extra current after removing the core.
  9. A paramagnet obeys χ = C/T, with χ = 9.0 × 10⁻⁴ at 300 K. Find χ at 450 K, and compare a diamagnet’s motion in the same field gradient.
  10. A fixed dipole P points +x. Compare the stable orientation and energy of an identical rotatable dipole Q held at equal far axial and equatorial distances r.
  11. Design a comparison that distinguishes a hard ferromagnet, a soft ferromagnet and a weak paramagnet.
  12. A 12 cm² flat surface in 0.20 T has its plane at 30° to B. Calculate flux for the normal making an acute angle with B, and explain the ideal Meissner-state contrast.

m = τ/(B sin30°) = 0.045/0.125 = 0.36 A m². Maximum torque occurs at 90° and is mB = 0.090 N m. A measured torque at one angle is not the maximum unless sinθ = 1.

Key Takeaways

Key Takeaways

• Magnetic moment describes a source; magnetisation describes moment density. • Far dipole geometry fixes both the axial/equatorial direction and the 2:1 magnitude ratio. • Torque is a cross product; energy and flux use dot products. • Parallel dipole alignment is the energy minimum; antiparallel alignment has zero torque but is unstable. • Closed-surface magnetic flux is zero even when the enclosed field is nonzero. • B, H and M are related but have different meanings; the simple material laws have stated conditions. • Diamagnetic, paramagnetic and ferromagnetic responses differ in mechanism, strength and magnetic memory. • Geometry, temperature, saturation and field history determine where an approximation is useful.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…