Skip to lesson content

Lesson 8 of 9

Electromagnetic Induction · Lesson 8 of 9

The AC Generator

“Derive a rotating coil’s alternating emf and connect waveforms, apparatus and energy supply.”

Learning Objectives

• Explain the function of the armature, slip rings and brushes. • Derive instantaneous emf for a uniformly rotating coil. • Relate flux and emf extrema to coil orientation. • Calculate peak emf and distinguish mechanical from electrical frequency.

A rotating coil changes its flux periodically

Mount a plane conducting coil on a shaft between magnetic poles. Choose the shaft perpendicular to the uniform field so that rotating the shaft changes the angle between the coil normal and B. The coil is the armature of this simple model. Its two ends connect to separate continuous slip rings fixed to the rotating shaft. Stationary brushes contact the rings and connect them to an external load. Each brush remains associated with the same coil end as the coil rotates.

The coil normal rotates from parallel to B through perpendicular to antiparallel and back again. Its signed flux therefore varies periodically. The two continuous slip rings allow the alternating terminal polarity to appear in the external circuit. A split-ring commutator performs a different switching function; replacing two slip rings with a split ring changes the output connection and must not be drawn as the same machine.

Generator connections: functional schematicRotating armatureAxis ⟂ BCoil ends A, BSeparate ringsbrushbrushLoadEach ring stays connected to the same coil end.
Armature, two slip rings, brushes and load— Functional connection diagram, not a spatial cross-section. The two rings are insulated from each other; grey brush contacts connect the rotating rings to a stationary load. Axis perpendicular to B is stated separately.

Derive the sinusoidal emf

Let the coil have N identical series turns, area A per turn and constant angular speed ω. At t = 0 take its normal parallel to B, so θ = ωt. The uniform field and area remain constant. Write the complete linkage before differentiating: λ = NBA cos(ωt). The derivative of cosine is negative sine, which cancels Faraday’s minus sign. A different initial orientation would shift the phase but leave the peak magnitude unchanged.

Flux and generated emfLaTeX
A is the area of one turn, B the uniform field, ω angular speed in rad s⁻¹ and N the turn count. The axis is perpendicular to B. Emf polarity is relative to the chosen winding direction and tracked normal.
Frequency in the simple two-pole modelLaTeX
For this one-pole-pair rotating-coil model, electrical frequency equals mechanical revolutions per second. In a multipole machine, electrical frequency equals pole-pair count times mechanical rotation frequency.

The waveform follows the slope of flux

Coil-normal angle θFlux linkageEmf
0°+NBA, maximum0
90°0, decreasing fastest+NBAω, positive peak
180°−NBA, minimum0
270°0, increasing fastest−NBAω, negative peak
360°+NBA0

When the coil plane is perpendicular to B, its normal is parallel or antiparallel to B. The flux magnitude is then greatest but its instantaneous rate of change is zero, so emf vanishes. When the coil plane contains B, its normal is perpendicular to B: flux is zero but changing fastest, so emf magnitude is greatest. Confusing flux with its derivative reverses these orientation predictions.

Normalised linkage (blue) and emf (red)0T/4T/23T/4Tλ/(NBA)ε/ε₀
A quarter-cycle separates flux and emf extrema— Both curves are dimensionless after normalisation. Red emf is positive when the blue linkage decreases. The vertical scale is not a common physical unit for flux and volts.
Pedal-driven coil

Problem
A 100-turn coil of area 0.10 m² rotates at 0.50 rev s⁻¹ in a 0.010 T field perpendicular to the shaft. Find peak emf.

  1. 1.Angular speed is ω = 2π × 0.50 = π rad s⁻¹. Peak emf is NBAω = 100 × 0.010 × 0.10 × π = 0.314 V.
  2. 2.At t = 0, with normal parallel to B, the instantaneous emf is zero. After T/4 = 0.50 s it reaches +0.314 V.
  3. 3.The peak value is not a constant output voltage. The coil produces an alternating waveform even at constant shaft speed.
Designing for peak voltage

Problem
A 200-turn coil has area 0.020 m², B = 0.40 T and frequency 25 Hz. Find peak emf and emf 1/8 cycle after the normal-parallel starting position.

  1. 1.ω = 50π rad s⁻¹. Peak emf = 200 × 0.40 × 0.020 × 50π = 80π V ≈ 251 V.
  2. 2.At t = T/8, phase is π/4, so emf = 251 sin(π/4) ≈ 178 V.
  3. 3.These are peak and instantaneous values respectively. They must not be labelled as RMS values; that distinction is developed when studying alternating circuits.

A generator converts energy

With an open external circuit the coil has generated emf but negligible load current. With a resistive load and negligible coil inductance, current follows the emf waveform. The current-carrying coil experiences a magnetic torque opposing its rotation. Maintaining speed requires mechanical input from a turbine, engine or person. Greater electrical loading demands greater input torque at the same speed, apart from changing losses. A magnetic field enables conversion; it is not a consumable fuel that replaces the mechanical energy source.

A falling-water turbine, steam turbine or wind-driven rotor can supply shaft energy. Real generators include winding resistance, friction, nonuniform fields and practical thermal limits. Many large machines use a rotating magnetic field and stationary armature windings to simplify high-power electrical connections. The simple rotating-coil model still teaches the flux-change principle, but its exact construction should not be asserted for every commercial generator.

Change one parameter at a time

At unchanged B, A and N, doubling ω doubles peak emf and doubles electrical frequency in the one-pole-pair model. Increasing N doubles ideal peak emf at unchanged speed, but does not change frequency; a real redesign also changes wire resistance and inductance. Increasing field magnitude or coil area raises peak emf while keeping frequency fixed if speed is fixed. These dependencies assume the axis remains correctly oriented and the same ideal uniform-field model applies.

If the shaft were parallel to B, rotating a fixed plane coil about that shaft would not change its normal’s component along B. The linked flux would be constant, so this generator mechanism would produce no emf. Likewise, changing the initial angle changes the timing of peaks, not their magnitude. Predicting these special cases checks the geometry more effectively than memorising a single sinusoidal formula.

Quick Quiz

Quiz

Quick check

A rotating-coil generator converts

Explanation: The shaft supplies work against electromagnetic torque under load.

Quick check

For normal initially parallel to B, emf at t = 0 is

Explanation: Flux is at an extremum and its slope is zero.

Quick check

At coil normal perpendicular to B, flux is zero and emf magnitude is

Explanation: Flux changes fastest at this orientation.

Quick check

Double shaft speed in a one-pole-pair ideal generator. Peak emf and frequency

Explanation: Peak emf ∝ ω and f = ω/(2π).

Quick check

The purpose of two slip rings is to

Explanation: Each continuous ring preserves its coil-end connection, allowing alternating polarity at the brushes.

Practice Problems

Practice Problems
  1. A coil has N = 50, A = 0.040 m², B = 0.20 T and f = 10 Hz. Find peak emf and period.
  2. For the preceding coil, find emf at t = 0.025 s if its normal is initially parallel to B.
  3. Why is maximum magnetic flux not the condition for maximum emf?
  4. A six-pole generator rotates at 1000 rpm. What electrical frequency follows from three pole pairs?
  5. A student doubles N and halves ω, leaving B and A fixed. Compare peak emf and frequency.

ω = 20π rad s⁻¹. Emf peak = 50 × 0.20 × 0.040 × 20π = 8π V = 25.1 V. Period = 1/10 = 0.10 s. The voltage varies through positive and negative values during each period.

Key Takeaways

Key Takeaways

• A rotating coil changes its linked flux by changing orientation. • Two slip rings preserve connections to the same coil ends. • With normal initially parallel to B, linkage is cosine and emf is sine. • Peak emf is NBAω under the stated ideal geometry. • Flux extrema coincide with zero emf, not peak emf. • Electrical frequency equals mechanical frequency only in the one-pole-pair model. • Mechanical work supplies electrical output and losses under load.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…