Electromagnetic Induction · Lesson 5 of 9
Rotating Rods and Conducting Wheels
“Integrate motional emf when different parts of a conductor move at different speeds.”
• Derive rotating-rod emf by adding local contributions. • Determine centre-to-rim polarity with a stated rotation and field. • Explain why parallel spokes do not multiply voltage. • Distinguish angular speed from rotation frequency.
Why one speed cannot describe a rotating rod
A rod pivots about one end in a plane perpendicular to a uniform magnetic field. Every point has the same angular speed ω but a different linear speed: a point at distance r moves with speed ωr. The pivot is stationary and the tip is fastest. Inserting the tip speed into Blv for the whole rod would pretend all segments move equally fast and overestimate the emf by a factor of two.
Divide the rod into short radial pieces of length dr. Each piece moves almost uniformly with local speed ωr, perpendicular to itself and B. Its small motional emf magnitude is Bωr dr. Since the pieces lie successively along the rod, their contributions add in series. The integral is therefore the area under a linearly increasing local-emf-per-length graph. This is the physical reason for the factor one half.
Polarity follows the cross product
View a wheel from the side toward which B points, so B is out of the page. For counterclockwise rotation, a point on the right-hand radius moves up; up crossed with out gives right, radially outward. Positive charge is driven toward the rim, making the rim positive relative to the centre in the isolated steady arrangement. Reverse either B or rotation and polarity reverses; reverse both and polarity is unchanged. Electrons tend to move toward the centre in the first case.
At open-circuit equilibrium the charge-separated electric field balances the radial magnetic force. That field is generally nonuniform because the magnetic contribution grows with r. The voltage magnitude is the radial integral of that field. Connecting an external circuit through contacts at the axle and rim lets the rotating conductor act as a generator; maintaining rotation against the electrical load requires mechanical torque.
A geometric check using swept area
In a time dt the rod sweeps a small sector of angle dθ = ωdt. Its area is one half R²dθ. The field times the swept-area rate is therefore one half BωR², agreeing with the local-force integral. The sector argument describes a circuit completed by a stationary return connection and a moving contact; it is not the flux through a fixed full disk changing merely because the disk rotates. When contacts change which material points form the circuit, keep the actual path and moving sections explicit.
Problem
A 1.0 m radial rod rotates at 50 rev s⁻¹ in a perpendicular 1.0 T field. Find emf magnitude.
- 1.Convert frequency: ω = 2π × 50 = 100π rad s⁻¹.
- 2.Emf magnitude = ½ × 1.0 × 100π × (1.0)² = 50π V ≈ 157 V.
- 3.Using 50 directly for ω would miss a factor 2π. Using tip speed over the whole rod would give twice the correct answer.
Problem
A 1.0 m rod rotates at 400 rad s⁻¹ in a 0.50 T axial field. Find centre-to-tip emf.
- 1.The supplied quantity is already ω, so no 2π conversion is needed. Emf = ½BωR² = ½ × 0.50 × 400 × 1.0 = 100 V.
- 2.The dimensional combination T × s⁻¹ × m² is Wb/s = V. The large value is possible because the tip speed is 400 m s⁻¹ in this ideal model; it is not a low-speed wheel.
Many spokes are parallel sources
For a wheel whose identical radial conducting spokes join the same axle and rim, every spoke has the same endpoints and the same centre-to-rim emf. They are connected in parallel, rather than end-to-end in series. Ten spokes therefore do not provide ten times the open-circuit voltage. More conducting paths can change effective resistance and load current, but those are separate questions requiring contact and material information.
Problem
A wheel has ten spokes of length 0.50 m and rotates at 120 rev min⁻¹ in an axial field of 0.40 G. Find axle-to-rim emf magnitude.
- 1.Use 1 G = 10⁻⁴ T: B = 4.0 × 10⁻⁵ T. Frequency is 120/60 = 2.0 Hz, so ω = 4π rad s⁻¹.
- 2.Emf = ½ × (4.0 × 10⁻⁵) × 4π × (0.50)² = 6.28 × 10⁻⁵ V, or 62.8 μV.
- 3.The number of spokes does not multiply this voltage because the spokes connect the same pair of terminals.
Generalisation and limits
If the rod lies between 0.20 m and 0.60 m from the axis, both ends move. The voltage depends on 0.60² − 0.20², not on (0.60 − 0.20)². If B varies with radius, integrate B(r)ωr dr. If B is not parallel to the axis, use the component contributing to the cross product along the conductor. These are geometric limitations of the simple formula, not exceptions to the underlying force law.
A rotating radial rod in an axial field can have constant-polarity emf. A closed plane coil rotating about an axis in its plane generally has alternating emf because its normal reverses relative to B. These generators use different moving-conductor geometries. Do not assume that every rotating conductor has sinusoidal output.
Quick Quiz
Quiz
A rotating rod pivots at one end. Its linear speed at radius r is
Explanation: Rigid rotation shares angular speed, not linear speed.
Using tip speed in Blv for the entire radial rod gives
Explanation: Local speed rises linearly from zero to tip speed.
120 revolutions per minute corresponds to ω equal to
Explanation: It is 2 revolutions per second, so ω = 2π × 2.
Ten equal spokes join one axle and one rim. Open-circuit voltage is
Explanation: Their emf sources connect in parallel between common endpoints.
For counterclockwise rotation and out-of-page B, the rim becomes
Explanation: The positive-charge magnetic-force tendency is outward.
Practice Problems
- Find emf for R = 0.40 m, B = 0.20 T and ω = 30 rad s⁻¹.
- At fixed B and ω, radius doubles. How does emf change and why?
- A radial conductor extends from 0.20 to 0.60 m in B = 0.50 T at ω = 10 rad s⁻¹. Find emf.
- Explain why reversing both rotation and field preserves polarity.
- A wheel gives 20 mV between axle and rim with 8 spokes. Would 16 identical spokes give 40 mV?
Integrate local contributions or use ½BωR² = 0.5 × 0.20 × 30 × 0.16 = 0.48 V. This is a magnitude; specify rotation and B directions to determine polarity.
Key Takeaways
• Different radii share angular speed but have different linear speeds. • Add local contributions Bωr dr to obtain rotating-rod emf. • A pivoted radial rod gives magnitude ½BωR² in uniform axial field. • State rotation and field directions before assigning polarity. • Convert revolutions per second to rad s⁻¹ using 2π. • Common axle-to-rim spokes connect in parallel. • An offset segment depends on the difference of squared radii.
Finished this lesson? Mark it complete to track your progress.
Loading your progress…