Skip to lesson content

Lesson 6 of 9

Electromagnetic Induction · Lesson 6 of 9

Mutual Induction and Coupled Coils

“Explain and calculate flux linkage and induced emf between neighbouring circuits.”

Learning Objectives

• Define mutual inductance with a clear source–receiver convention. • Derive mutual inductance of long coaxial solenoids. • Use reciprocity to choose a simpler field calculation. • Calculate induced emf and flux-linkage change separately.

A changing current can act across an insulating gap

Place two insulated coils near one another. A current in coil 2 produces a magnetic field, part of which passes through coil 1. If the current in coil 2 changes, the flux linkage of coil 1 changes and an emf appears in coil 1. Electrical contact between the coils is unnecessary. Energy is transferred through their electromagnetic interaction; the receiver is not receiving conduction electrons directly from the source coil.

To describe this coupling, hold both coils fixed and assume a linear magnetic medium. Doubling source current doubles its field and the resulting receiver flux linkage. Their ratio is a property of the geometry, orientations and medium. In this approximation it stays constant while the current changes. Moving a coil or saturating an iron core can change that ratio, so the simplest proportional model must then be reconsidered.

Define the source and receiver explicitlyLaTeX
Subscript 12 means flux linkage of receiver 1 due to source current 2. The emf formula assumes M₁₂ is constant. Φ is per-turn flux due to the other coil, not total flux from all sources.

The henry is the SI unit of inductance: 1 H = 1 Wb/A = 1 V s/A. A mutual inductance magnitude of 1 H produces 1 V of induced emf when the source current changes at 1 A s⁻¹. A large steady current may create large linked flux but produces no mutual emf once it stops changing. A smaller rapidly changing current may produce a much larger emf.

Derive M for two long coaxial solenoids

Let two very long coaxial solenoids overlap over length l. The inner one has area A₁ and n₁ turns per metre; the outer one has area A₂ greater than A₁ and n₂ turns per metre. First pass source current I₂ through the outer solenoid. Neglect end effects: its field in the inner region is B₂ = μ₀n₂I₂. Each inner turn links B₂A₁, and the inner coil has N₁ = n₁l turns. Multiply to obtain its total linkage.

Outer source, inner receiverLaTeX
Air or vacuum core; both coils are long compared with their radii, coaxial and overlapping over l. n is turns per metre. The shared linked area is A₁.

Now reverse the roles. Source current I₁ through the inner solenoid gives B₁ = μ₀n₁I₁ mainly within its own cross-section. Although an outer turn encloses area A₂, the ideal inner-solenoid field occupies only A₁. Thus flux through each outer turn is B₁A₁, not B₁A₂. Multiplying by n₂l gives the same coefficient. This shared-area argument is the central geometric step; using the larger coil’s full area overestimates coupling.

Inner source, outer receiverLaTeX
For stationary reciprocal linear media with consistent winding references, the mutual coupling coefficients are equal. With a common linear core filling the relevant field region, replace μ₀ by μ = μᵣμ₀.
Long coaxial solenoids: side view, schematicOuter turns: n₂ per metreInner field region: area A₁M = μ₀ n₁ n₂ A₁ l
Only the shared field area links both solenoids— The blue strip represents the inner solenoid’s field region in side view. A₁ is its cross-sectional area perpendicular to the common axis; shaded side-view area is not the area to insert in M.
A solenoid pair

Problem
Air-core coaxial solenoids have n₁ = 1000 m⁻¹, n₂ = 1500 m⁻¹, A₁ = 2.0 × 10⁻⁴ m² and l = 0.50 m. Find M and emf when I₂ rises at 20 A s⁻¹.

  1. 1.M = (4π × 10⁻⁷)(1000)(1500)(2.0 × 10⁻⁴)(0.50) = 1.885 × 10⁻⁴ H.
  2. 2.The induced emf magnitude is M|dI₂/dt| = 3.77 × 10⁻³ V. With the positive linkage convention above, an increasing positive I₂ gives negative receiver emf.
  3. 3.A high turn density does not by itself guarantee a large voltage; shared area, overlap length and current-change rate all matter.

Use reciprocity to avoid a difficult field integral

Consider concentric single-turn circular loops with radii a and b, where a is much smaller than b. The large loop’s field is nearly uniform over the small loop and approximately equals its central field μ₀I/(2b). Calculating the reverse linkage directly is harder because the small loop’s field varies over the large loop’s surface. Reciprocity lets us calculate the easy direction and use the same M in reverse.

Unequal concentric circular loopsLaTeX
Single-turn, coplanar, coaxial air-core loops. For tightly grouped multiple turns with the same geometry, multiply by the turn counts of both coils. This is a small-loop approximation, not an exact formula for similar radii.
Small loop at the centre

Problem
Two single-turn concentric loops have radii a = 0.010 m and b = 0.10 m. Estimate M.

  1. 1.M ≈ (4π × 10⁻⁷)π(0.010)²/(2 × 0.10) = 1.97 × 10⁻⁹ H.
  2. 2.The value is about 2.0 nH. It is small because a one-turn small receiver encloses little area. The ratio a/b = 0.10 supports an approximate central-field calculation; the formula would fail as a approaches b.

Linkage change is not emf

If current rises by ΔI₂, the receiver linkage changes by MΔI₂. The induced average emf additionally requires division by the time interval and a minus sign. A question asking change in flux linkage is answered in Wb-turn; a question asking emf is answered in V. Likewise the per-turn flux change is linkage change divided by N₁ when equal linkage per turn is justified.

If both circuits carry changing currents, the linkage of coil 1 includes its own contribution and the other coil’s: λ₁ = L₁I₁ + M₁₂I₂ in a fixed linear model. Its induced emf is the negative derivative of that sum. Winding references determine the sign of M in a circuit equation. Coupling strength and induced-current direction are related but separate issues: use geometry and Lenz’s law rather than assuming every secondary current flows opposite to a primary current arrow.

Quick Quiz

Quiz

Quick check

A mutual inductance of 0.20 H and source-current rate 3 A s⁻¹ give emf magnitude

Explanation: M|dI/dt| = 0.20 × 3.

Quick check

Source current is constant and coils are fixed in a linear medium. Mutual emf is

Explanation: Linked flux is steady, so its derivative vanishes.

Quick check

For long coaxial solenoids, the relevant area in M is

Explanation: Only the inner field area contributes when the inner solenoid is the source.

Quick check

In the fixed reciprocal linear arrangement, M₁₂ and M₂₁ are

Explanation: The same coupling coefficient describes the two directions.

Quick check

MΔI has the units of

Explanation: H × A = Wb-turn, whereas emf also involves a time rate.

Practice Problems

Practice Problems
  1. M = 1.5 H and source current rises from 0 to 20 A in 0.50 s. Find linkage change and average emf magnitude.
  2. For a 200-turn receiver in the preceding problem, find per-turn flux change if all turns link equal flux.
  3. Double the outer radius of long coaxial solenoids while retaining inner area, turn densities, overlap length and air core. What happens to ideal M?
  4. For unequal concentric single-turn loops, derive the approximate dependence of M on small and large radii.
  5. A detector signal changes when one coil is moved away. Is constant M still justified?

Δλ = MΔI = 1.5 × 20 = 30 Wb-turn. Average emf magnitude = Δλ/Δt = 30/0.50 = 60 V. The supplied time affects emf but not endpoint linkage change.

Key Takeaways

Key Takeaways

• Mutual induction couples circuits through a changing linked magnetic field. • M relates receiver flux linkage to source current in a linear fixed geometry. • Mutual emf depends on current-change rate, not current alone. • Long coaxial solenoids share the inner cross-sectional field area. • Reciprocity can replace a difficult reverse field calculation. • Changing linkage MΔI and induced emf MΔI/Δt are different quantities. • Varying geometry requires differentiating the full product MI.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…