Skip to lesson content

Lesson 7 of 9

Electromagnetic Induction · Lesson 7 of 9

Self-Induction and Magnetic Energy

“Derive solenoid self-inductance, interpret back emf and calculate stored field energy.”

Learning Objectives

• Explain why a coil opposes changes in its own current. • Derive the self-inductance of a long solenoid. • Distinguish induced emf from passive terminal voltage. • Derive stored magnetic energy and field energy density.

A coil reacts to its own changing current

When current begins to grow in a coil, its own magnetic field and flux linkage grow. Faraday’s law applies to this self-produced flux just as it applies to a neighbouring coil’s flux. The resulting induced emf opposes the growth. When current decreases, the induced emf tends to maintain it. A coil therefore resists change in current, rather than always resisting current in one fixed direction.

In a fixed linear magnetic environment the self-produced linkage is proportional to current. The proportionality L is called self-inductance. It depends on geometry and permeability, not on the chosen current value within the linear model. If a core saturates, permeability and the linkage–current relation become nonlinear; a single constant L may no longer describe every operating point. We use the constant-L model unless stated otherwise.

Self-linkage and back emfLaTeX
L is self-inductance in H. The negative sign expresses opposition to the chosen positive current’s change. For time-dependent L use −d(LI)/dt rather than −L dI/dt alone.

At steady current dI/dt = 0, so an ideal inductor has no induced emf even though its field and stored magnetic energy can be nonzero. A real coil also has winding resistance and can require a nonzero steady terminal voltage IR. Inductance and resistance have different effects: resistance dissipates energy continuously, whereas ideal inductance stores and returns field energy.

Derive L for a long solenoid

Let a long solenoid have length l, cross-sectional area A and N turns, with turn density n = N/l. Neglect edge fields and take a uniform linear core permeability μ. The interior field is B = μnI. Each turn links approximately BA, and total linkage is NBA. Substituting N = nl gives λ = μn²AlI. Divide by I to obtain the inductance.

Long-solenoid inductanceLaTeX
Use μ₀ ≈ 4π × 10⁻⁷ H m⁻¹ for air/vacuum calculations at this precision. Uniform field, negligible end effects and a linear core are assumed. A is in m², l in m and n in m⁻¹.

Doubling N at fixed length and area increases L by a factor of four: each ampere produces twice the field and twice as many turns link it. Increasing length at fixed N lowers turn density and reduces L. Increasing length at fixed turn density instead adds turns and increases L. These two length changes must not be confused. A high-permeability core can increase L, but hysteresis and saturation limit the simplest model for real magnetic materials.

An air-core inductor

Problem
A long solenoid has N = 1000 turns, l = 0.50 m and A = 2.0 × 10⁻⁴ m². Find L and the self-induced emf when current rises at 50 A s⁻¹.

  1. 1.L = μ₀N²A/l = (4π × 10⁻⁷)(10⁶)(2.0 × 10⁻⁴)/0.50 = 5.03 × 10⁻⁴ H = 0.503 mH.
  2. 2.Self-emf is −L dI/dt = −0.0251 V in the positive-current reference. Its magnitude is 25.1 mV, opposing the rise.
  3. 3.If current falls at the same rate magnitude, the self-emf reverses and tends to sustain the original current.

Terminal voltage has a reference convention

Label an ideal inductor’s terminal voltage vL using the passive convention: positive at the terminal where reference current enters. The externally applied voltage needed for a rising current is vL = +L dI/dt. The self-induced emf around the positive current direction is −L dI/dt. These opposite signs describe the applied terminal drop and internal opposing emf, rather than contradictory physics. For a real coil, terminal voltage includes RI as well.

A source driving a resistive inductorLaTeX
This is Kirchhoff’s voltage equation for a fixed series R–L circuit with the stated references. No detailed transient solution is needed here. At long-time DC, dI/dt = 0 and I = V/R.

For finite applied voltage, ideal-inductor current cannot jump discontinuously: an instantaneous jump would require an unbounded dI/dt and hence unbounded voltage in the model. Opening a real circuit rapidly can therefore produce a large voltage and possibly a spark while magnetic energy is transferred into the available circuit, capacitance and surroundings. This does not mean every coil produces the same switch-off voltage; the decay path controls it. Predicting such a voltage requires more information than L and initial current alone.

Build the field by doing work

During a small increase dI in current, the source supplies power against the inductive terminal voltage. Ignoring resistive heating, the instantaneous storage power is vLI = LI dI/dt. Multiplying by dt gives dU = LI dI. Integrate from zero current, taking L constant, to obtain the stored energy. The source’s energy has not vanished into an ideal inductor; it can be returned when current decreases.

Energy in a constant-L inductorLaTeX
U is in joules. Inductance must be constant for this simple integral result. Unlike Joule heating, stored energy depends on the final current and can ideally be recovered.
Energy and a current decrease

Problem
A 0.20 H ideal inductor initially carries 3.0 A. Its current later falls to 1.0 A. Find released magnetic energy.

  1. 1.Initial energy = ½ × 0.20 × 3.0² = 0.90 J. Final energy = ½ × 0.20 × 1.0² = 0.10 J.
  2. 2.The decrease is 0.80 J. It can be delivered to a load or dissipated in the actual decay path. It is incorrect to calculate ½L(ΔI)² because the difference of squares is not the square of the difference.

Energy resides in the magnetic field

For an air-core long solenoid substitute L = μ₀n²Al and I = B/(μ₀n) into U = ½LI². The n² factors cancel, leaving B²Al/(2μ₀). Divide by the interior volume Al to obtain energy per unit volume. The expression reveals that doubling field strength quadruples field energy density in vacuum.

Magnetic field energy density in vacuumLaTeX
u is in J m⁻³. The vacuum field-energy expressions are general; the solenoid and parallel-plate capacitor provide simple derivations. In a uniform linear medium u_B = B²/(2μ); nonlinear or hysteretic media require more care.
Current I (A)t (s)εself < 0εself = 0εself > 0
A current ramp and its opposing self-emf— Constant positive L. A positive slope gives opposing negative self-emf; a falling positive current gives positive self-emf that supports the current.
Field energy density

Problem
An approximately uniform air-core magnetic field is 0.020 T in volume 1.0 × 10⁻³ m³. Estimate field energy.

  1. 1.uB = (0.020)²/[2(4π × 10⁻⁷)] = 159 J m⁻³.
  2. 2.U = uB × volume = 0.159 J. The estimate neglects energy in fringing fields outside the stated ideal uniform region.
  3. 3.The units provide a check: B²/μ₀ has units of energy density, so multiplying by m³ gives joules.

Quick Quiz

Quiz

Quick check

When a positive coil current is decreasing, its self-emf tends to

Explanation: Self-induction opposes decrease as well as increase.

Quick check

Double N at fixed solenoid length, area and permeability. L becomes

Explanation: L = μN²A/l.

Quick check

An ideal inductor at constant nonzero current has

Explanation: Derivative is zero, while ½LI² is not.

Quick check

For passive terminal references, ideal-inductor voltage is

Explanation: The positive applied terminal drop balances the negative self-induced emf.

Quick check

Current doubles in a constant-L inductor. Stored energy becomes

Explanation: Energy is proportional to I².

Practice Problems

Practice Problems
  1. Current falls from 5 A to zero in 0.10 s while average induced-emf magnitude is 200 V. Estimate L.
  2. A 0.50 H ideal inductor has current rising linearly from 1 A to 3 A in 0.20 s. Find self-emf and energy increase.
  3. A solenoid length doubles. Compare L if N is fixed and if n is fixed.
  4. Derive the energy density of an ideal air-core long solenoid.
  5. Why can opening a coil circuit generate a large voltage without creating energy?

For constant L and monotonic decrease, |average emf| = L|ΔI|/Δt. Thus L = 200 × 0.10/5 = 4.0 H. The induced emf supports the initially flowing current; this determines direction separately from magnitude.

Key Takeaways

Key Takeaways

• Self-induction opposes changes in current rather than current itself. • For constant L, self-emf is −L dI/dt. • A long linear-core solenoid has L = μN²A/l. • State what is held fixed before applying proportional reasoning. • Passive terminal voltage and induced emf use different sign references. • Stored energy is ½LI² for a constant-L inductor. • Vacuum magnetic field energy density is B²/(2μ₀). • Switch-off voltage transfers existing field energy rather than creating energy.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…