Skip to lesson content

Lesson 2 of 7

Dual Nature of Radiation and Matter · Lesson 2 of 7

Measuring the Photoelectric Effect

“Interpret a photoelectric apparatus and distinguish changes in electron number from changes in maximum electron energy.”

Learning Objectives

• Explain the roles of emitter, collector, window, voltage supply and current meter. • Predict how collector potential changes photocurrent. • Relate stopping-potential magnitude to maximum initial kinetic energy. • Separate the effects of intensity and frequency using controlled comparisons.

Measure two things, not one

When illumination produces current, a meter tells us how much charge reaches the collector per second. It does not directly measure how fast the electrons left the emitter. A stronger current may mean more electrons with the same energy distribution. To measure the upper end of that distribution, oppose the electrons with a known electric potential difference and find when none can reach the collector.

An evacuated tube with a controllable collector

A photosensitive emitter C and collector A face each other in an evacuated tube. Light enters through a window and falls on C. Quartz is useful for ultraviolet light because ordinary glass can absorb it. A variable supply controls the collector potential relative to the emitter; reversing the supply changes an accelerating arrangement into a retarding one. A voltmeter is connected across A and C. A microammeter is in series in the external circuit. Vacuum reduces collisions with gas, allowing the current to reveal emitted-electron behaviour more directly.

Photoelectric apparatus: voltmeter parallel, current meter seriesMeasure current and plate potentialEmitter CCollector AEvacuated tubeLightQuartz windowElectron motionShown: V = V_A − V_C > 0Variable VμAV
Photoelectric apparatus and polarity— The voltmeter is across the plates; the current meter and variable supply complete the external series circuit. Shown with collector positive.
A signed collector potentialLaTeX
V is in volts; ΔU is the electron’s electric potential-energy change in joules for travel from C to A. Positive V reduces electron potential energy and accelerates collection.

The arrow for electron motion from emitter to collector is opposite the conventional-current direction through the tube. In a sustained experiment the external circuit replenishes the emitter. The supply changes electron collection and adds or removes kinetic energy after emission; it does not by itself change the light energy absorbed in the initial photoelectric event. Very strong fields that modify the surface barrier belong to a different regime.

Increase collector potential at fixed illumination

Keep material, frequency and intensity fixed. At a positive collector potential, some initially misdirected or slow electrons can be drawn toward A. Increasing the voltage generally increases the fraction collected. Eventually essentially all available emitted electrons are collected and the current reaches a plateau: saturation current. Raising the voltage further increases arrival energy, but cannot provide more photoelectrons per second when the emission rate is fixed. This is why the current does not keep increasing like that through a simple fixed resistor.

A current can exist at V = 0 because emitted electrons already possess kinetic energy; a battery does not need to launch every electron. At negative V the collector repels electrons. Only those with sufficient suitable kinetic energy overcome the retarding barrier. The current decreases because the emitted energies and directions are distributed. A single sharp initial energy for all electrons would not explain the gradual decline.

Stopping-potential energy measurementLaTeX
Vₛ ≥ 0 is the stopping-potential magnitude: the collector voltage at cutoff is V = −Vₛ. The speed formula is nonrelativistic. Ideal geometry, negligible contact-potential offsets and dark-current subtraction are assumed.

For a retarding potential V = −Vₛ, the electron’s potential energy rises by eVₛ. At cutoff this removes the maximum initial kinetic energy available for reaching the collector, giving Kmax = eVₛ. In a planar description it is the kinetic component normal to the retarding barrier that matters; the ideal edge is interpreted as Kmax when electrons directed toward the collector are available. Contact potentials and geometry must be allowed for in precision measurements. Vₛ is a positive magnitude, not a negative kinetic energy.

Reading a cutoff correctly

Problem
The collector voltage at disappearance of current is −1.50 V relative to the emitter. Find Kmax in eV and joules and estimate vmax.

  1. 1.The stopping magnitude is Vₛ = 1.50 V, so Kmax = 1.50 eV = 2.40 × 10⁻¹⁹ J.
  2. 2.For a slow electron, ½mₑvmax² = Kmax. Thus vmax = √[2(2.40 × 10⁻¹⁹)/(9.11 × 10⁻³¹)] = 7.26 × 10⁵ m/s.
  3. 3.This is about 0.0024c, supporting the nonrelativistic approximation. The negative collector voltage retards a negative electron; the kinetic energy remains positive.

Change intensity while holding frequency fixed

For a fixed surface and a frequency above its threshold, raising intensity increases the number of emission events per second in the ordinary linear regime. Saturation current therefore rises in proportion to intensity, while stopping magnitude remains the same. The current–voltage curves have different plateau heights but the same negative-voltage cutoff. This is the decisive separation between electron number and maximum initial energy.

Saturation current proportional to intensity at fixed frequencyAbove threshold, fixed f and surfaceiₛ (μA)Intensity (W/m²)iₛ ∝ intensity0
Current versus intensity at fixed frequency— Above threshold in the linear response regime; other experimental conditions are fixed.
Current curves at a common frequency with different intensitiesFixed frequency: vary intensityPhotocurrent i (μA)Collector voltage V (V)−Vₛ0Higher intensityCommon cutoff; different saturation currents1.01.62.2
Intensity changes the plateau, not the cutoff— Idealised smooth curves at one frequency and one surface. Their detailed shapes are schematic; all share the same stopping voltage.
Counting electrons from saturation current

Problem
At saturation a cell gives 0.80 μA. After a change of illumination it gives 2.00 μA, with the same stopping magnitude. What changed?

  1. 1.Collected-electron rate is current/e. Initially it is (0.80 × 10⁻⁶)/(1.602 × 10⁻¹⁹) = 4.99 × 10¹² s⁻¹.
  2. 2.Finally the rate is 1.25 × 10¹³ s⁻¹, a factor 2.5 larger. Under unchanged frequency and efficiency, intensity increased by that factor.
  3. 3.The unchanged stopping magnitude means the maximum initial kinetic energy stayed the same; the current alone would not establish this.

Change frequency and watch the energy edge

A given surface has a threshold frequency f₀. Below it there is no ordinary single-photon photoemission, even with brighter light. Above it, higher frequency produces a larger stopping magnitude. The graph of stopping magnitude against frequency is linear for a fixed surface. Photoemission has no detectable energy-accumulation delay in the standard observations, with reported response times of order 10⁻⁹ s or less; this does not mean every point emits an electron at the instant light is switched on.

Compare frequency curves by their cutoff positions. Higher frequency moves cutoff to a more negative collector voltage. Equal plateau heights can be chosen for a schematic comparison by matching emission rates. They are not a universal consequence of holding intensity, measured in W/m², constant. At different frequencies, equal optical power means different photon numbers per second, and the probability of emission can also change. Thus plateau height cannot establish frequency independence of electron energy.

Current curves for increasing frequency with matched emission ratesHigher frequency: larger stopping magnitudePhotocurrent i (μA)Collector V (V)0−Vₛ₃f₃−Vₛ₂f₂−Vₛ₁f₁f₃ > f₂ > f₁Equal plateaus here assume matched emission rates.
Frequency changes the stopping voltage— Plateau heights are matched by choice of emission rates; equal optical intensity alone does not guarantee this.
Change madeKeep fixedReliable inference in the standard regime
Increase intensityFrequency, surface and geometryHigher saturation current; same stopping magnitude.
Increase frequency above thresholdSurface; control other variablesHigher stopping magnitude; plateau depends on photon rate and efficiency.
Make collector more positiveIllumination and surfaceGreater collection until saturation.
Use sufficiently negative collector voltageIllumination and surfaceZero collected photocurrent, although emission can continue.

A fair measurement and its limitations

Subtract any dark current measured with the light blocked. Vary only one quantity at a time; keep illuminated area and surface preparation fixed. For a distant point-like source at fixed spectrum, increasing distance reduces intensity approximately as 1/r², but changing geometry too close to the lamp need not follow that law. Record the zero-current cutoff repeatedly rather than assuming a tiny current is exactly zero. Filters must transmit the intended band: a small high-frequency leak can cause emission when the nominal colour is below threshold.

Predict and resolve

At V = −Vₛ the meter reads zero. Has the light stopped ejecting electrons? No. The retarding field can turn emitted electrons back. Emission at the surface and arrival at the collector are separate processes.

Quick Quiz

Quiz

Quick check

The collector is at +2 V relative to the emitter. What does the electric field do to an electron moving toward it?

For an electron, ΔU = −eΔV. A positive potential change lowers potential energy, increasing kinetic energy in lossless motion.

Quick check

Current becomes zero at collector voltage −0.80 V. What is Kmax?

The stopping magnitude is 0.80 V and Kmax = eVₛ = 0.80 eV.

Quick check

At fixed above-threshold frequency, doubling intensity in the linear regime does what?

Intensity controls emission-event rate at fixed frequency; the maximum energy is fixed by frequency and surface.

Quick check

Why does the current reach saturation?

The supply can increase arrival energies after saturation, but the fixed emission rate limits current.

Quick check

What follows from equal intensity at two different frequencies?

Intensity is energy per area per time. Photon rate and wavelength-dependent emission efficiency both matter for saturation current.

Practice Problems

Practice Problems
  1. At saturation, 6.0 × 10¹² electrons reach the collector each second. Find the current magnitude and explain what doubling the positive collector voltage does once saturation is reached.
  2. Two curves at the same frequency have plateau currents 1.2 μA and 3.6 μA and a common cutoff −0.65 V. Compare intensity and maximum initial energy.
  3. An electron leaves the emitter with 0.60 eV along the collector direction. Can it cross a retarding difference of 0.90 V? What is its energy after a +0.90 V accelerating difference?
  4. Design a controlled experiment to test whether intensity determines maximum electron energy.
  5. A distant small lamp gives saturation current 4.0 μA at 0.50 m. Predict the current at 1.0 m, and state whether the stopping magnitude changes.

Use i = eṄ = (1.602 × 10⁻¹⁹)(6.0 × 10¹²) = 9.6 × 10⁻⁷ A = 0.96 μA. With the emission rate fixed, doubling an already saturating voltage does not raise the current; it raises electron arrival energy.

Key Takeaways

Key Takeaways

• Photocurrent measures charge arrival rate; stopping potential measures an energy edge. • Use V = V_A − V_C and a positive stopping magnitude Vₛ with cutoff V = −Vₛ. • Kmax = eVₛ in the ideal corrected measurement. • Positive collector voltage improves collection until saturation. • At fixed above-threshold frequency, intensity changes saturation current without changing Kmax. • Frequency changes the stopping magnitude; equal-intensity plateaus need not be equal. • Zero collected current can occur while photoemission continues.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…