Skip to lesson content

Lesson 6 of 10

Moving Charges and Magnetism · Lesson 6 of 10

Magnetic Fields of Solenoids

“Explain how coil fields combine and derive the ideal long-solenoid field with explicit geometric limits.”

Learning Objectives

• Explain the field pattern of a finite and an ideal long solenoid. • Derive B = μ₀nI using an appropriate rectangular path. • Count turns per unit length including multiple winding layers. • Distinguish a useful uniform-field approximation from a real finite device.

Many loops make a useful field region

A solenoid is a wire wound into closely spaced helical turns. Enamel insulation prevents neighbouring turns from making electrical contact and short-circuiting the intended winding. When the pitch is small, each turn is approximately a circular current loop. The magnetic field at any point is the vector sum of the contributions from all turns. Along the central axis their contributions reinforce; outside, substantial cancellation makes the field weaker.

A finite solenoid has a strong, approximately axial field near its central interior and a weaker return field outside. Field lines close through the surrounding space rather than beginning and ending on the coil. At the ends the field spreads and is less uniform. Do not interpret a drawing of straight interior arrows as evidence that the exterior field is identically zero for a finite device.

××××××××××B inside →Upper turns out; lower turns inoutside ≈ 0
A solenoid cross-section with a rectangular integration path— Side cross-section: upper currents emerge from the page and lower currents go into it. Their rightward interior fields add. The red path samples an interior length h and an exterior return.

Define the long-solenoid approximation

A solenoid is long when its length L is much greater than its radius a. Far from its ends, many nearby turns contribute while the geometry varies little along the axis. In the infinite tightly wound idealisation the interior field is uniform and axial and the exterior field vanishes. For a long but finite solenoid these are approximations near its middle. Closely spaced turns also suppress small-scale variations between individual windings.

The winding density n = N/L is turns per metre, with N the total number of turns distributed along length L. Turns are counted without a physical unit, so n has unit m⁻¹. If the winding has several layers, count all their turns; using only one layer understates the total enclosed current. For a thick winding, differences in radii and local field geometry can limit the simple thin long-solenoid model.

Derive the ideal interior field

Choose a rectangular Amperian path with one long side of length h inside the solenoid parallel to the field, the other outside, and two short sides transverse to the axis. In the ideal limit, the outside side contributes zero because B outside is zero. The short sides contribute zero because B is perpendicular to dl. The inside side contributes Bh. The surface cuts nh turns, each carrying I across it with the same sign.

Apply Ampere’s lawLaTeX
This is the air-core or vacuum long-solenoid result. h is the chosen interior path length; it cancels and is not the total coil length.

The unit check is (T m A⁻¹)(m⁻¹)(A) = T. The result does not explicitly contain radius, because in the long idealisation the geometry and superposition produce cancellation of that dependence. This does not mean every finite coil has a radius-independent centre field. The assumptions must still be satisfied after a change in radius or length.

A long, narrow coil

Problem
A solenoid is 0.50 m long with 500 turns, radius 1.0 cm and current 5.0 A. Estimate its central field.

  1. 1.n = N/L = 500/0.50 = 1000 m⁻¹. The ratio L/a = 50 supports the central long-solenoid approximation.
  2. 2.B ≈ μ₀nI = (4π × 10⁻⁷)(1000)(5.0) = 6.28 × 10⁻³ T.
  3. 3.The field is axial with direction given by curling fingers along the winding current. This is an estimate near the centre, not a claim of uniformity at every end point.

Direction, polarity and controlled changes

Look at one end of the solenoid. If the current appears anticlockwise, the field emerges from that end: it acts as the north end. A clockwise circulation gives the south end. Reversing current reverses both ends. Within the winding region the field runs from the south end toward the north end, while the exterior return field completes the loops.

Predict what happens if the same coil is stretched to twice its length with N and I fixed. The turn density halves, so the central field approximately halves while the long-solenoid approximation remains applicable. If instead turns are added in proportion to length, n stays constant and the ideal central field stays constant. The phrase “longer coil” alone is therefore not enough to predict a field change.

Multiple winding layers

Problem
An 80 cm solenoid has five layers of 400 turns each and carries 8.0 A. Its diameter is 1.8 cm. Estimate the central field.

  1. 1.Total N = 5 × 400 = 2000; n = 2000/0.80 = 2500 m⁻¹. The length is much larger than the 0.009 m radius.
  2. 2.B ≈ (4π × 10⁻⁷)(2500)(8.0) = 2.51 × 10⁻² T. Counting only 400 turns would give one fifth of this estimate.
  3. 3.The estimate assumes a sufficiently thin closely wound arrangement and negligible magnetic-material effects.

How to investigate the model

With a low-voltage current source, a current meter and a magnetic-field probe, compare the central field for several steady currents without changing coil geometry. The ideal prediction is a straight B-versus-I line with slope μ₀n. Background fields can create an offset; subtract a zero-current reading or compare opposite current directions. Avoid presenting fabricated measurements as observations. Coil heating can change current if voltage rather than current is controlled.

A soft magnetic core can make the field much larger, but the vacuum formula alone no longer describes the material response. Permeability can depend on field, history and geometry; an arbitrary constant multiplier is not a complete model. Here we keep the quantitative derivation to the air-core geometry and retain the qualitative distinction between finite and ideal fields.

Quick Quiz

Quiz

Quick check

At fixed geometry, doubling solenoid current approximately makes its central air-core field

Explanation: The long-solenoid result is linear in current.

Quick check

A solenoid has three layers of 200 turns over 0.60 m. Its n is

Explanation: Total turns are 600, divided by 0.60 m.

Quick check

Why do the transverse sides of the ideal rectangular Amperian loop contribute zero?

Explanation: The dot product vanishes for perpendicular field and path direction.

Quick check

Which statement about a finite solenoid is correct?

Explanation: Finite coils have exterior return fields and end effects.

Quick check

Stretching a long coil to twice its length at fixed N and I approximately changes B to

Explanation: The turn density N/L halves, provided the same model remains valid.

Practice Problems

Practice Problems
  1. A 0.40 m coil contains 800 turns and carries 2.0 A. Find its ideal central field.
  2. How many turns over 0.50 m are needed for 4.0 mT at 2.0 A?
  3. A fixed-N solenoid’s length increases by 25% and its current decreases by 20%. Find the field ratio.
  4. Viewed from one end, winding current is anticlockwise. Identify that end and the interior axial direction near it.
  5. Design a comparison that distinguishes a current-dependent coil field from a fixed background field.

n = 800/0.40 = 2000 m⁻¹. B = μ₀nI = (4π × 10⁻⁷)(2000)(2.0) = 5.03 × 10⁻³ T. This assumes an air core and a length large compared with radius.

Key Takeaways

Key Takeaways

• A solenoid’s field is the vector sum of its loop fields. • Finite solenoids have exterior return fields and nonuniform ends. • The ideal long-solenoid interior field is axial and uniform. • For an air core, B ≈ μ₀nI near the middle of a long coil. • Count all layers when calculating n = N/L. • The rectangular path works because of field direction and exterior approximation. • Changes in length matter through turn density and model validity.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…