Skip to lesson content

Lesson 1 of 7

Semiconductor Electronics · Lesson 1 of 7

Energy Bands and Semiconductor Materials

“Explain why materials conduct differently by connecting crystal energy bands, available electronic states and the energy gap.”

Learning Objectives

• Distinguish conductors, semiconductors and insulators using electrical behaviour. • Interpret valence and conduction bands as allowed electron energies. • Calculate an energy gap and use conductivity and resistivity consistently. • Explain the limits of simple material classifications.

Why a tiny piece of silicon can control current

A copper connecting wire should carry current easily. The plastic around it should prevent current from escaping. A silicon device has a different purpose: its ability to conduct can be controlled by temperature, light, a small concentration of added atoms and an applied voltage. That controllability makes semiconductors useful in electronic circuits. To understand it, we need more than the statement that silicon has a resistance between those of copper and plastic. We need a model of the electronic states available inside the solid.

Earlier electronic devices often used electrons emitted from a heated cathode into an evacuated tube. Heating, large operating voltages and bulky arrangements made such devices inconvenient for many uses. A solid-state device uses charge carriers within a solid; it does not need a vacuum enclosure or a heater simply to provide its carriers. Early crystal detectors also used a metal point contact on galena, lead sulphide (PbS), to detect radio signals through rectifying behaviour. Solid-state components can be small, operate with modest power and offer long useful life, although actual ratings vary by device. A diode is one such device. We will build its explanation from the material upward rather than assuming that a small component must behave like an ordinary resistor.

Recall current, resistance and material properties

Current is charge crossing a section per second. For a uniform piece of material, resistance also depends on its length and cross-sectional area. Resistivity isolates the material contribution at specified temperature and other conditions. Conductivity describes the same response in the reciprocal way. In this chapter these quantities refer to ordinary weak-field material behaviour; a complete diode, whose internal conditions change with voltage, need not obey a constant-resistance law.

Resistivity and conductivityLaTeX
R is in Ω, length L in m, area A in m², resistivity ρ in Ω m and conductivity σ in S/m. The reciprocal relation compares the same material under the same conditions.
Material familyElectrical behaviourExamples
ConductorMany carriers can respond to a small field; relatively low resistivity.Copper, aluminium and other metals.
SemiconductorCarrier populations can change strongly with temperature, illumination or doping.Elemental silicon and germanium; compounds such as GaAs, CdS, CdSe and InP.
InsulatorOrdinary conditions provide very few mobile electronic carriers.Glass, many plastics and diamond.

Typical resistivity ranges span many powers of ten. Broad illustrative ranges are about 10⁻⁸–10⁻² Ω m for metals, 10⁻⁵–10⁶ Ω m for semiconductors and 10¹¹–10¹⁹ Ω m for good insulators. These overlap or shift with material, purity and temperature; they are not sharp definitions. Organic and polymer materials can also show semiconducting behaviour. Our microscopic examples use crystalline silicon and germanium. In compound semiconductors, departures from the ideal constituent ratio and the resulting crystal defects can also change carrier populations. For example, gallium-rich and arsenic-rich GaAs have different defect environments. The carrier type depends on the actual defect chemistry; a simple universal rich-element-to-carrier rule is not assumed here.

Read a material property

Problem
A uniform sample has resistivity 2.0 Ω m, length 2.0 mm and cross-sectional area 0.50 mm². Find its conductivity and resistance.

  1. 1.Convert the geometry: L = 2.0 × 10⁻³ m and A = 0.50 × 10⁻⁶ m². The area conversion is squared because 1 mm² = 10⁻⁶ m².
  2. 2.Conductivity is σ = 1/ρ = 0.50 S/m. Resistance is R = 2.0 × (2.0 × 10⁻³)/(0.50 × 10⁻⁶) = 8.0 × 10³ Ω.
  3. 3.The result is 8.0 kΩ for this particular shape. Doubling the length doubles R but does not change ρ or σ if material conditions remain fixed.

From isolated atoms to allowed energy bands

An isolated atom has discrete allowed electron energies. When a very large number of atoms form a crystal, their electronic states interact. Closely spaced allowed energies form bands. Between some bands are intervals with no allowed electronic states in the ideal crystal. Such an interval is a forbidden energy gap. A band diagram plots electron energy vertically. It is not a picture of shelves located at different heights inside the material.

Silicon has four outer-shell electrons, in 3s and 3p states; germanium also has four, in 4s and 4p states. In a simple state-counting picture, N atoms contribute 4N valence electrons and 8N available outer-shell one-electron states, including spin. The interacting states separate into a lower band with 4N available states and an upper band with 4N states. At zero temperature in ideal intrinsic silicon, the lower band is full and the upper one empty. The detailed band structure requires quantum mechanics, but this occupancy picture is enough for the reasoning here.

The lower relevant band is called the valence band. The upper one is the conduction band. Write Eᵥ for the highest valence-band energy and E꜀ for the lowest conduction-band energy. The gap is the separation between those two edges, not the energy measured from an arbitrary zero. One electron volt is the energy gained by a charge of magnitude e through a potential difference of one volt: 1 eV = 1.602 × 10⁻¹⁹ J.

Energy gapLaTeX
E꜀ and Eᵥ must use a common reference. The difference is an energy, usually given here in eV. The forbidden gap contains no allowed bulk states in the ideal undoped-crystal model.
Allowed bands and occupancy in different materialsAllowed electron energies and occupancyEnergyMetalSemiconductorInsulatorOccupiedEmpty statesPartly filled bandE_gValenceConductionSmaller gapE_gValenceConductionLarger gapAlso metallic: overlapping bands. Gaps and occupancy are schematic.
Allowed bands and material behaviour— Energy increases upward. Coloured bands contain allowed states; the white separation is an energy gap, not an empty spatial layer. Partial occupancy and overlapping bands are two possible metallic cases.

Why band occupancy matters

An electric field slightly changes the motion and occupation of electronic states. For an electron to contribute to conduction, nearby available states must permit that response. A completely filled band cannot acquire a net ordinary conduction current simply by moving every occupied state into another already occupied state. A partially filled band has accessible unoccupied states close in energy. Metals can have a partially filled band or overlapping bands, so they do not need substantial thermal excitation across a forbidden gap before conducting.

In a semiconductor the gap is small enough that thermal excitation can move some valence electrons into the conduction band at ordinary temperatures. This simultaneously creates vacancies in the valence band. Both kinds of mobile carrier matter. In an insulator with a large gap, the same temperature creates far fewer such carriers. Silicon has a gap of about 1.1 eV and germanium about 0.7 eV near room temperature. Diamond has a gap around 5.4 eV and ordinarily behaves as an insulator. Graphite is a different carbon structure and must not be assigned diamond’s behaviour merely because both contain carbon.

A rule of thumb sometimes places semiconductor gaps below a few eV and insulator gaps above that range. It is only a guide: wide-band-gap semiconductors exist. Conductivity depends on carrier concentrations and how readily carriers move, not on gap size alone. Similarly, the band gap of a solid is not the ionisation energy needed to remove an electron from an isolated atom. The crystal’s collective states determine its gap.

Compare gaps without confusing the energy zero

Problem
Two ideal band sketches give material A: Eᵥ = −5.0 eV, E꜀ = −3.9 eV; material B: Eᵥ = −4.0 eV, E꜀ = −3.3 eV. Calculate both gaps and predict which is more easily thermally excited if other factors are comparable.

  1. 1.For A, E_g = −3.9 − (−5.0) = 1.1 eV. For B, E_g = −3.3 − (−4.0) = 0.7 eV. Both are positive separations between band edges.
  2. 2.A smaller gap requires less energy for a valence-to-conduction transition. Thus B is more easily thermally excited in the comparison described.
  3. 3.The prediction concerns the excitation cost. It does not establish a universal conductivity ratio because carrier mobility and other material properties can differ.

Read the diagram, then predict a change

At ideal zero temperature an intrinsic semiconductor has no thermally excited carriers. On warming it, some conduction-band states become occupied and an equal number of valence-band states become empty. The gap is not a physical door that opens, and the bands need not overlap for conduction to begin. The next lesson follows those excited electrons and vacancies and explains why two carrier types appear even in a chemically pure crystal.

Quick Quiz

Quiz

Quick check

What does a forbidden energy gap represent?

The vertical coordinate is electron energy, not position. Allowed states form bands, and the forbidden interval separates band edges in the ideal model.

Quick check

Which feature allows ordinary metallic conduction?

An electric field can change occupied states when nearby unoccupied states are accessible. A filled isolated band does not provide that ordinary response.

Quick check

If E꜀ = −2.5 eV and Eᵥ = −3.6 eV, what is E_g?

Subtract the valence-band edge from the conduction-band edge: −2.5 − (−3.6) = 1.1 eV. The arbitrary energy zero cancels.

Quick check

A material has ρ = 5.0 Ω m. Its conductivity is

Use σ = 1/ρ under the same conditions. The reciprocal of Ω m is S/m, so both the numerical reciprocal and the unit must change.

Quick check

Why can diamond and silicon behave differently despite both having four valence electrons per atom?

Equal valence count does not require identical band energies. Diamond’s much larger gap makes thermal excitation far less effective under ordinary conditions.

Practice Problems

Practice Problems
  1. A sample has ρ = 0.040 Ω m, L = 5.0 mm and A = 2.0 mm². Calculate σ and R.
  2. The top of a valence band is at −6.0 eV and the bottom of a conduction band at −4.8 eV. Find the gap in eV and joules.
  3. For N silicon atoms, count the valence electrons and the available states in each of the two bands in the simple zero-temperature picture. Explain why a full lower band does not imply metallic conduction.
  4. Rank diamond, silicon and germanium by approximate band gap, then explain the limitation of using that ranking to predict conductivity.
  5. A student says the conduction band is physically above the valence band, so electrons must move upward through the sample to conduct. Correct the explanation.

Convert L = 5.0 × 10⁻³ m and A = 2.0 × 10⁻⁶ m². Then σ = 1/0.040 = 25 S/m and R = 0.040 × 0.005/(2.0 × 10⁻⁶) = 100 Ω. These describe different things: σ is a material response, whereas R also includes the chosen shape.

Key Takeaways

Key Takeaways

• A semiconductor is useful because its electronic conduction can be controlled. • Resistivity belongs to the material under specified conditions; resistance also depends on shape. • Allowed atomic states combine into energy bands in a crystal. • The band gap is E_g = E꜀ − Eᵥ and has units of energy. • Band occupancy and accessible empty states explain ordinary conduction. • Small gaps favour thermal excitation, but gap size alone does not fix conductivity. • Band diagrams plot energy, and the solid-state gap differs from isolated-atom ionisation energy.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…