Skip to lesson content

Lesson 5 of 7

Semiconductor Electronics · Lesson 5 of 7

Diode Bias and Current–Voltage Characteristics

“Connect terminal polarity to junction physics, measure a nonlinear diode characteristic and distinguish static from incremental resistance.”

Learning Objectives

• Identify the anode, cathode and bias polarity of a junction diode. • Explain forward injection, reverse leakage and breakdown. • Read diode I–V data with signed axes and appropriate current units. • Calculate current limiting and distinguish V/I from ΔV/ΔI.

A diode does not treat both voltage polarities equally

Put a junction diode and a resistor in series with a low-voltage supply. For one diode orientation an appreciable current can flow; reverse the orientation at the same modest supply magnitude and the current becomes very small. This is rectifying behaviour. It follows from how external voltage changes the built-in barrier, rather than from a rule that the component is always either a perfect wire or a complete gap.

A semiconductor diode has two terminals connected to its p and n regions. The p-side terminal is the anode A and the n-side terminal is the cathode K. In the ordinary diode symbol, the cathode is the bar side. Conventional forward current travels from anode to cathode. Always identify that bar before deciding whether a circuit is forward or reverse biased. A physical package often marks the cathode with a band, but the package identification should be checked for the actual component.

Anode, cathode and applied bias polarityForward current: anode p → cathode nA: pK: nCathode barConventional forward currentForward biaspnLimited supply+−Narrower barrierReverse biaspnLimited supply−+Wider barrier
Diode terminals and external bias— The cathode bar is on the n-side. Forward bias connects p to supply positive and n to negative through a current-limited circuit; reverse bias swaps that polarity. The diode voltage is Vᴅ = Vₐ − Vₖ.
Terminal sign conventionLaTeX
Vᴅ is in volts and Iᴅ in amperes. Forward bias has Vᴅ > 0; reverse bias has Vᴅ < 0. The same signs apply to the I–V graph.

Forward bias lowers the barrier

Connect p to positive and n to negative. The applied field across the depletion region opposes the built-in field. The effective barrier is reduced and the depletion region narrows. More majority electrons can cross n→p and more majority holes can cross p→n. After crossing, these carriers are minorities in their new regions: this is minority-carrier injection. Excess injected carriers spread into the neighbouring neutral material and recombine. The external circuit replenishes carriers and sustains current.

Barrier change in the simple junction pictureLaTeX
V_F and V_R are positive magnitudes for forward and reverse bias. These qualitative barrier relations describe the ordinary junction regime; do not extrapolate them to arbitrary large forward voltage or breakdown.
Junction barrier reduced forward and increased reverseBias changes the effective junction barrierBarrier potentialpnxZero bias: V₀Forward: V₀ − V_FReverse: V₀ + V_RLocal p-side references aligned; profiles are schematic.Forward bias narrows depletion; reverse bias widens it.
Bias changes the junction barrier— These qualitative potential profiles compare the junction barrier at zero bias, forward bias and reverse bias. Each uses its local p-side reference; the applied terminal voltages are not the plotted barrier heights.

With p on the left, injected electrons move left and injected holes right, but both contribute rightward conventional forward current. A little increase of forward voltage can produce a large increase in carrier injection, so the I–V characteristic bends upward. There is no exact universal turn-on voltage. Values around 0.7 V for silicon and around 0.2–0.3 V for germanium are useful rough descriptions at certain currents and temperatures, not thresholds below which all current is mathematically zero.

Reverse bias increases the barrier

Connect p to negative and n to positive. The applied field reinforces the depletion field, the depletion width grows and majority diffusion is strongly suppressed. Thermally produced minority electrons on the p-side and holes on the n-side can still reach the depletion region and be swept across it. Their conventional current is from cathode to anode, negative in our sign convention. Ordinary reverse leakage can be tiny compared with forward current, but it is not exactly zero.

Over a useful range the reverse current changes much less with voltage than forward current does, giving an approximately saturated part of the curve. Its magnitude depends strongly on material, temperature and device construction. A generic sketch may show μA reverse current and mA forward current, but those are illustrative scales, not universal ratings. Increasing reverse voltage far enough causes breakdown and a rapid current rise. If external current limiting and device power ratings are neglected, either forward overcurrent or reverse breakdown current can overheat a diode.

Illustrative forward and reverse diode characteristicsSame voltage convention; different current scalesForward: I_D (mA)V_D (V)00.7Smooth nonlinear riseReverse: I_D (μA)V_D < 0I_D < 0BreakdownSmall leakageMore reverse voltage ←Separate panels: reverse current is not on the forward mA scale.
Forward and reverse I–V behaviour— The forward and reverse panels use different current scales, explicitly mA and μA. These are illustrative curves, not a calibration of one commercial diode. The reverse plot shows the small leakage region before breakdown and the abrupt increase beyond it.

Measure a characteristic without confusing the meters

Use an isolated adjustable low-voltage source, a series current-limiting resistor and an ammeter in series. Put the voltmeter across the diode itself. Take several readings of diode voltage and current, increasing the source in small steps while watching current and power limits. Reverse the diode for reverse-bias readings and use a meter range suitable for the smaller current. A resistor protects the diode and the ammeter; a current meter must not be connected directly across a supply. No mains connection is needed for this study.

Ammeter series and voltmeter parallel across the diodeMeasure diode voltage, limit the series currentAVariable supplyR limitDiode+−VA in series; V across the diode; isolated low-voltage source.For reverse readings, switch supply off before reversing the diode.
Measuring the diode characteristic— The ammeter and resistor are in the main loop; the voltmeter is across the diode. Source voltage includes the resistor drop, so it must not be substituted for measured diode voltage on the graph. Reverse the diode only with supply off.

Record temperature where possible, because warming changes the characteristic. A reverse microampere reading needs more care than a forward milliampere reading: meter leakage, resolution and contact quality can matter. Plot Iᴅ vertically against Vᴅ horizontally. Mark the units and do not silently stretch the reverse scale to look comparable with the forward current. The origin defines zero terminal voltage and zero net current, not the disappearance of the internal junction barrier.

Two meanings of resistance must stay distinct

For a resistor with a straight line through the origin, V/I and the local change ΔV/ΔI are equal. For a nonlinear diode they generally differ. Static or dc resistance is the ratio of the voltage and current at one operating point. Incremental or small-signal resistance is the local slope of V against I around that point, approximated from nearby readings. If the graph instead plots I against V, the incremental resistance is the reciprocal of its slope.

Static and incremental resistanceLaTeX
Both are in Ω. Use signed V and I consistently; a reverse point normally has both negative. ΔV/ΔI approximates the local tangent only over a sufficiently small interval.
Read a forward slope and a dc ratio

Problem
A local forward characteristic passes through 0.70 V at 10 mA and 0.80 V at 20 mA. Estimate incremental resistance near 15 mA and compare dc resistance at the interpolated midpoint.

  1. 1.The local changes are ΔV = 0.10 V and ΔI = 10 mA = 0.010 A. Thus r_d ≈ 0.10/0.010 = 10 Ω.
  2. 2.Using linear interpolation only over this interval, the midpoint is approximately 0.75 V at 0.015 A. Its dc ratio is R_dc ≈ 0.75/0.015 = 50 Ω.
  3. 3.The 10 Ω secant does not pass through the origin. The different 50 Ω dc ratio is not a contradiction: one describes nearby changes and the other the full operating-point ratio.
Interpret a small reverse reading

Problem
At Vᴅ = −10 V a diode has Iᴅ = −1.0 μA. Calculate dc resistance and state what cannot be deduced from this point alone.

  1. 1.Convert −1.0 μA to −1.0 × 10⁻⁶ A. R_dc = (−10)/(−1.0 × 10⁻⁶) = 1.0 × 10⁷ Ω = 10 MΩ.
  2. 2.This single point does not give reverse incremental resistance. That requires nearby voltage-current differences or the local tangent.
  3. 3.A nearly horizontal I-versus-V leakage curve can have an incremental resistance much larger than its dc ratio. The μA unit is essential: using mA would make the ratio a thousand times too small.

The external resistor chooses a safe operating point

Design with an explicitly approximate diode drop

Problem
A 5.0 V supply drives a forward silicon diode through 1.0 kΩ. Use a constant 0.70 V drop model to estimate current and resistor power.

  1. 1.The resistor receives the remaining voltage: V_R = 5.0 − 0.70 = 4.30 V. Hence I = V_R/R = 4.30/1000 = 4.30 mA.
  2. 2.Resistor power is I²R = (0.00430)² × 1000 = 0.0185 W, about 19 mW. The diode dissipates approximately V_DI = 3.0 mW.
  3. 3.These are model estimates, not exact diode predictions. A real operating point is where the diode curve and the circuit relation I = (V_s − V_D)/R agree, and selected components must meet their ratings.

A diode’s asymmetric response suggests a useful application. If an alternating input changes sign, the diode can pass mainly one polarity. Two appropriately connected diodes can route both half-cycles through a load in the same direction. The next lesson follows those complete circuit paths rather than treating rectification as a change in the AC source itself.

Quick Quiz

Quiz

Quick check

The anode is 0.60 V above the cathode. The diode is

Forward bias is a polarity condition, Vₐ − Vₖ > 0. It does not require an exact universal 0.70 V threshold; the resulting current depends on the actual characteristic.

Quick check

Under ordinary forward bias, the depletion region generally

The applied field opposes the built-in field, reducing the barrier and depletion width in the usual junction regime. Increased injection explains the forward current.

Quick check

A small reverse leakage current before breakdown is associated mainly with

Reverse bias suppresses majority diffusion but the field can collect thermally available minority carriers. Their supply and generation conditions affect leakage strongly.

Quick check

Nearby readings give ΔV = 0.06 V and ΔI = 3.0 mA. The incremental resistance is

Convert 3.0 mA to 0.0030 A, then use r_d ≈ ΔV/ΔI = 0.06/0.0030 = 20 Ω. A V/I ratio at a single point answers a different question.

Quick check

How should the voltmeter be connected when measuring diode I–V data?

The graph needs the voltage across the diode itself. The series resistor has its own drop, and current limiting protects the diode and the current meter.

Practice Problems

Practice Problems
  1. For p left and n right, state the bias and barrier change when p is at +0.4 V relative to n, then when p is at −2 V relative to n.
  2. A diode has 8 mA at 0.68 V and 12 mA at 0.72 V. Estimate incremental resistance and the dc resistance at the interpolated midpoint.
  3. At −8.0 V the reverse current is −2.0 μA. Calculate the dc ratio and explain why this does not establish incremental resistance.
  4. Choose a resistor for approximately 5.0 mA from a 6.0 V source using a 0.70 V diode-drop model. Find resistor power.
  5. A student draws reverse current on the same mA scale as forward current, labels all reverse readings zero, and calls the diode a perfect one-way wire. Identify the three modelling problems.

At +0.4 V the junction is forward biased: its applied field opposes the built-in field, reducing the barrier and narrowing depletion. At −2 V it is reverse biased: the barrier increases and depletion widens. The first voltage may give measurable current; polarity, not an exact 0.7 V number, defines the bias.

Key Takeaways

Key Takeaways

• The anode is the p-terminal; the cathode is the n-terminal and bar side of the symbol. • Forward bias means Vₐ > Vₖ and generally lowers the barrier and narrows depletion. • Reverse bias increases the barrier; small minority-carrier leakage remains before breakdown. • A quoted silicon forward drop is an approximation that depends on operating conditions. • Measure diode voltage across the diode and use a series current-limiting circuit. • Static resistance V/I and incremental resistance ΔV/ΔI are different for a nonlinear diode. • Track μA, mA, signs and power limits when interpreting diode data.

Finished this lesson? Mark it complete to track your progress.

Loading your progress…